Acer Aspire 5100 Motherboard Replacement

Geschrieben von: Brad Rollinson
  • Kommentare: 14
Acer Aspire 5100 Motherboard Replacement

Schwierigkeitsgrad

Difficult

Schritte

20

Zeitaufwand

30 - 40 Minuten

Einleitung

This guide will show you how to replace the motherboard in an Acer Aspire 5100 laptop. This is needed when your laptop begins to shut down or freeze. A motherboard can also be referred to as a mainboard. A motherboard is an essential part of a computer system. This can be used if you need to change the hardware or clean it. This task can serve to help you complete any repairs or upgrades you want to make. Be aware this replacement requires a lot of delicate work.

  1. 5JYbqAR3hqQ2ZnWp

    • Flip the laptop upside-down.

    • Remove the battery as a safety precaution.

    • Remove the four screws attached to the large panel.

  2. qTUshOoMcJ4kVSfj

    • Lift and remove the panel.

  3. WShqyaNVJwOrBkKy

    • Remove the two screws attached to the fan.

  4. EFnTvAWjOcWEqWgL
    EFnTvAWjOcWEqWgL
    SGNQn1EPAWlNSxW1

    • Lift the fan and detach the cable that connects the fan to the motherboard.

    • The fan can break easily. Be careful when removing.

    • When detaching the cable, do not pull on the cable itself. Instead, use a small spudger to detach it at the white section that connects it to the motherboard.

  5. 3CVCFQEOCHSwbPne
    3CVCFQEOCHSwbPne
    4cNyx4QLTsCSxCgP

    • Open and push the screen back all the way until it is horizontal with the rest of the laptop.

    • Use an opening tool to remove the panel above the keyboard that has the power button on it.

    • After you have released the tabs, lift up the panel.

  6. 2Koddgf6WOX2awTp
    2Koddgf6WOX2awTp
    YEaUnxRHeb5jjres
    sFaZiLYUmr1VWwpu

    • Under the panel, remove the two screws that connect the keyboard to the laptop.

    • One screw is located above the F5 button, and the other one is located above the F10 button.

    • Potential for device damage: Lift up the keyboard CAREFULLY because there is a ribbon that connects the keyboard to the motherboard.

  7. 2uiaJyNJNtLxVifk

    • Release the catch on the ribbon socket by sliding the two tabs toward the ribbon.

    • Pull the ribbon under the keyboard to detach it from the motherboard.

    • Remove the keyboard.

    do not pull on ribbon it will only break the cable. instead use tool to detach from mother board. i broke mine by pulling ribbon.

    steve foss -

    useless guide, there are a lot of screws that lock the cover on the laptop and you have never showed them

    Valerio Vischio -

    You do not need to remove the whole cover, in order to replace the keyboard.

    The description for this job is right.

    The switch plate cover just pops off.

    Screws revealed, secure the keyboard.

    Unclip the ribbon cable.

    Job done

    Richard -

  8. myqUC4XTPmBWmoNb

    • Remove the nine screws from the back edges of the laptop.

  9. egNqMoXCMIG5aJtA
    egNqMoXCMIG5aJtA
    CLtQZOHL6amq1Zjb
    wqREsT6njMNZQEFM

    • Open the lid of the laptop and locate the cover that surrounds the keyboard and track pad.

    • Use the spudger to pry open the sides of this cover.

    • DO NOT lift cover off after detaching it because the track pad is connected to the motherboard.

  10. TTEFFSMuR5JNiJX1
    TTEFFSMuR5JNiJX1
    CPFS1uHUQBFxNDN4

    • Slightly lift up the cover to see the ribbon connection.

    • Release the catch by sliding the two lugs toward the ribbon, then pull the ribbon to detach it from the motherboard.

    • Lift up the cover from the laptop.

  11. bpyFcUoH5L3D1WO6

    • On the cover that was removed, flip it around and locate where the back of the track pad is.

    • Remove the three screws located at the corners.

    • Lift up the bracket that you just unscrewed and remove track pad.

  12. O1KwWn6wQvJONLJc

    • Remove the two screws from each corner beneath the LCD screen.

  13. vWof1LjgVC4BeaGV
    vWof1LjgVC4BeaGV
    S2uFu45IPmgsTLTI

    • Detach the white rectangle located on the motherboard at the end of the wire connected to the LCD screen.

  14. jwSoGZZLmVANpIbf
    jwSoGZZLmVANpIbf
    I3W2wlAHHk4cAHVn

    • Flip the laptop upside down.

    • Remove the four screws from the back panel of the laptop.

    • Lift the panel up and set it aside.

  15. HVQNUIjUGZHPrsWU

    • Detach the black and white wire.

    • You do not need to remove the cooling fan.

  16. 41iOcEBfjXdakMdE

    • Lift up the monitor to detach it.

  17. fVIUrNHdkAD3P6Yt

    • Remove the 15 screws from the motherboard.

    • There is normally only one remaining screw attached to the motherboard on the bottom right beneath the tape.

    • All the other screw holes (except screws holding the base cover on) are kept empty.

  18. oaySr5ucKuhMeRDQ

    • Flip the laptop upside down.

    • Locate the heat sink, which is the copper "L" shaped component, and unscrew the four screws that connect it to the motherboard.

  19. XPOljUqykuIYcH4r

    • Push out the back of the casing by the VGA connector to remove the motherboard.

  20. TjNU4hOpTNwxktl6
    TjNU4hOpTNwxktl6
    S4EvgRFv3YQjdPDe

    • Lift up and remove the motherboard from the laptop casing.

    • Remove the USB add-on card to use it with the new motherboard.

    • To remove, grab on the sides and lift upward.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Brad Rollinson

Mitglied seit: 29/09/10

1113 Reputation

6 Kommentare

que tipo de motherboard puedo comprar para una laptop acer aspire 5100-3357

KALALA -

Thank you. I followed the guide as closely as possible. I am installing Windows 76 Ultimate on it again.

Thank you!

rogers518086 -

a lot of stuff missing in terms of unscrewing certain screws to get the cover off. I got stuck at step 10 because the cover was still attached by various screws.

Maybe I have a different model, but it is for sure an Acer Aspire 5100.

I also broke a lot of connection where screws thread in to, hopefully it goes back together rigidly enough.

Jamie Beurklian -

It is not neccessary for a full strip down, just to get at the CPU. Access from the main cover, remove fan and heatsink. The CPU can now be removed as in the final steps.

Richard -

You have to remove the video cable, wifi cables and LCD before you try to remove the touchpad/upper cover. You must also remove two screws from the bottom labeled 10x. In other words, you should complete steps 12 to 16 and remove the 10x screws before attempting to complete steps 9 to 11.

Nelson Mata -

The Fan must also be removed before removing the touchpad/upper cover.

Nelson Mata -