Afridev Axle and Handle Replacement

Geschrieben von: Jake Devincenzi
  • Kommentare: 0
Afridev Axle and Handle Replacement

Schwierigkeitsgrad

Moderate

Schritte

10

Zeitaufwand

Keine Schätzung

Einleitung

This guide will show you how to remove both the axle and the handle, so that you can replace either one or both.

  1. FhPbCTNvohW3y6Ce
    FhPbCTNvohW3y6Ce
    waXx4TtWIhXF1BnF

    • Assemble the required tools, including the Afridev tool and crescent wrenches.

  2. gJrvuPQEkX1UumLA
    gJrvuPQEkX1UumLA
    FYeV5eQbwykFiGWJ
    qUA1IloNsXRdp26B

    • Perform a water test on the pump, by raising and lowering the handle a full 40 strokes. A properly performing pump will yield greater than 10 liters.

  3. IWA1LIds4LCSOdNf
    IWA1LIds4LCSOdNf
    C5MEHDf2OafhsRHo

    • Loosen the bolt on front of the face plate with the Afridev tool.

    • Remove the plate from the pump by lifting it straight up.

  4. wrEawT23OkuYMc5y
    wrEawT23OkuYMc5y
    5kDOChRTUEaaIsdJ
    rqq3ijWHpeFkjHXJ

    • Insert the T-handle into the top cylinder of the exposed pump rod.

  5. pgG5VmlTyhKxOHpw
    pgG5VmlTyhKxOHpw
    amyGDp5JbAlFaHAL

    • Loosen the 2 bolts on either side of handle.

    • It is not necessary to remove the bolt at this time; however, take caution to not let the bolt fall out of the handle.

  6. BGMVmB3GKVkfVQfk
    BGMVmB3GKVkfVQfk
    aXnBFwWQVSLgXX5L
    TnOOubFGMJtHHG6p

    • Loosen the 2 bolts on either side of the head to remove the handle from the pump rod.

    • It is not necessary to remove the bolt at this time; however, take caution to not let the bolt fall out of the handle.

  7. nNxmxoNQDVDXMcFG
    nNxmxoNQDVDXMcFG
    dHqn6KCLWQk2ChXC

    • Lift the handle to a horizontal position.

  8. pYELvZHDGJE6VNQX
    pYELvZHDGJE6VNQX
    hPRlGvX4RbcN5Sgh
    COKQQcdWLsbMls5D

    • While one person lifts up on the T-handle, remove the bolt and connection pieces.

  9. KhlCA6Mptm4bGw3N
    KhlCA6Mptm4bGw3N
    jjgUiFhJ1QsRn4Y5
    N5HOJbGvWS1kZUJx

    • Remove the bolt and connection pieces from the handle.

    • Set the bolt pieces in a sanitary place, such as a bucket, to prevent contamination.

  10. vc35hWOSsVT6mRVV
    vc35hWOSsVT6mRVV
    ZOSLdTRFFOLG5KFC

    • Remove the handle from the pump.

    • Be sure to set the handle in a sanitary place to prevent contamination.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Jake Devincenzi

Mitglied seit: 18/04/11

116297 Reputation

0 Kommentare