Aiptek DZO-V58N Speaker Replacement

Geschrieben von: Zachary Yun
  • Kommentare: 0
Aiptek DZO-V58N Speaker Replacement

Schwierigkeitsgrad

Moderate

Schritte

13

Zeitaufwand

30 - 35 Minuten

Einleitung

The speaker plays back recorded sounds when you are watching video on the LCD screen of the device. Use this guide to replace the speaker.

  1. OOqyZKRSIklZQSpM

    • Locate the battery compartment on the back of the camera. It is the panel with the plastic ridges for simple removal.

    • Slide the battery compartment cover down off of the camera body.

  2. Fw5xBtaSJrwuNZvU

    • Pry up the battery from the bottom using a finger and remove the batter from the case.

  3. xVIsTAFL2Z2IAsUL

    • Remove the lanyard by pulling the grey lace through the black string loop.

    • Pull black string loop through the silver bracket.

  4. cBEAwhPeuNJGQZ4E

    • Use a plastic opening tool to pry off the black control cover.

    • The face plates are glued, so use force to pry the face plates from the camera body.

  5. Wm4eIgT1MQVf6kP5

    • Use a plastic opening tool to pry off the ridged back face plate and the black button.

    • The face plates are glued, so use force to pry the face plates from the camera body.

    • The button is loose and should come off with little or no effort.

  6. UYUsAhBOT25CEIPh

    • Use a plastic opening tool to pry off the silver face plate.

    • The face plates are glued, so use force to pry the face plates from the camera body.

  7. SWa3XPvbWoBJyWsT
    SWa3XPvbWoBJyWsT
    AFxDToQCRTlEjbfF
    2eTYeBAUFvBnSScF

    • Open the USB cover to expose the small machine screw.

    • Use the Phillips #00 screwdriver to unscrew the six 0.5cm machine case screws (distributed around the camera body).

    • These small screws are easy to lose. Place the removed screws in an organized container to avoid losing them.

  8. OvlTexHADePWhcOy

    • Pull off the side control panel.

  9. odiw2WE1OHdy5BUK
    odiw2WE1OHdy5BUK
    hmIaCujZTKKaPPuq

    • Flip open the screen by pulling the loose end of the screen away from the case.

    • Use tweezers to remove the two outside rubber dots to reveal the two 0.5cm machine screws.

    • Use the #00 Phillips Screwdriver to remove both screws.

  10. OYTvwRZeuJMYwwDI
    OYTvwRZeuJMYwwDI
    JWYHkndOG2WJs5ZO

    • Pull the body apart from the bottom of device just enough to make space to remove the silver plastic strap holder.

    • Use tweezers to remove the silver plastic strap holder.

    • Use a plastic opening tool to pry off the lens protector.

  11. YGNu6JAMEPCJcWQP
    YGNu6JAMEPCJcWQP
    NGeZDdJ6yMRHFo6c
    ysBkphKLkAHUgfMq

    • Unscrew the two silver 0.5cm machine screws with the #00 Phillips screwdriver.

    • Lift off the lens protector housing.

    • Pull apart the two halves of the camera body.

    • Do not pull the two halves apart too far because the wires may detach.

  12. PLLrRT4IrZxXXwL6

    • Use the #00 Phillips screwdriver to unscrew the two black speaker screws.

    • Lift off plastic cover.

  13. ZHycBTXwqk1oJWEf

    • Unplug the speaker from the circuit board by pulling out the white plastic connector.

    • Make sure to pull plastic connector and not wires because the wires could be damaged.

    • Lift out the speaker.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Zachary Yun

Mitglied seit: 04/04/12

7 Reputation

0 Kommentare