Apple Watch Series 2 Klebestreifen austauschen

Geschrieben von: Dominik Schnabelrauch

Kommentare: 15

Apple Watch Series 2 Klebestreifen austauschen

Schwierigkeitsgrad

Mittel

Schritte

Zeitaufwand

45 Minuten - 1 Stunde

Einleitung

Benutze diese Anleitung, um die Klebestreifen an deiner Apple Watch Series 2 auszutauschen, damit das Gerät wieder verschlossen werden kann. Die Apple Watch ist nach dem Austausch der Klebestreifen unter Umständen nicht mehr vollständig wasserdicht.

Werkzeuge

Ersatzteile

Schritt 1

Tränke ein Wattestäbchen mit etwas Isopropylalkohol (>90%) oder benutze ein Reinigungstuch, um damit vorsichtig alle Klebereste auf der Force Touch Dichtung zu entfernen.
Um den Kleber auf der Seite zu entfernen, wo die Displaykabel verlaufen, musst du das Display nach unten klappen und es vorsichtig vom Rahmen wegziehen, um genug Platz zu haben.

I bought 6 adhesive strips expecting to foul up some. I tried following this procedure on three of the sets, but on each set I ended up with one corner not quite long enough to seat properly. On the fourth set I altered the procedure and it finally worked the first time.

1. Take off the screen. Yes I know, but do it anyway.

2. Take off only the blue adhesive around the periphery. Do not remove center area.

3. Place sticky side on force gasket. Seems small, but fit perfectly.

4. Remove entire inner rectangular portion of adhesive strip

5. Replace screen

6. Re-Attach battery

7. Follow rest of procedure

marilyntlinton - 03/11/19

The isopropyl alcohol can only remove so much of the old adhesive. After the first pass with the q-tip use an iFixit Opening Tool to carefully scrape off the old adhesive. There is always some left on the case.

Vangelis Angelakis - 19/05/21

Schritt 2

Drehe die Apple Watch um, sodass das Display flach liegt, und hebe das Gehäuse hoch.
Entferne alle Klebereste auf der Rückseite des Displays.

Schritt 3

Löse den Ersatzklebestreifen mit der blauen Schutzfolie vorsichtig mit einer Pinzette vom Trägerpapier ab.

Be sure to buy two, three or even more replacement adhesive strips, because depending on the batch or brand, most of them can’t be separated easily, they deform and then they are next to useless.

@iFixit - Guys check the adhesives you are sending to people. The Tesa ones are simply a nightmare to use.

Vangelis Angelakis - 19/05/21

Agreed! The strip is EXTREMELY challenging to get off the paper/plastic it comes in - I recommend a very sharp ‘Xacto’, or scalple blade to trim the paper & plastic film (carefully) to allow for the very thin & easily damaged strip from the packaging - let alone getting it place. Vangelis’ adice is sound advice. I had to order two more… (wish me luck)

Jeff Goodall -

Thank you both for the heads up! The Tesa brand adhesive was super finicky (my tab broke off pretty early on) but was able to recover with minimal deformation with a blade to remove the unnecessary plastic.

Felipe Agurto -

Schritt 4

Halte den Ersatzklebestreifen diagonal, um ihn über das Display zu führen.
Kippe das Display leicht nach vorne, damit du den Klebestreifen mit dem Rahmen ausrichten kannst.
Positioniere den Ersatzklebestreifen auf der Force Touch Dichtung und benutze die Spudgerspitze, um ihn gerade auszurichten und festzudrücken.

Den Klebestreifen zu positionieren ist extrem schwer. Teils wegen unzureichender Passgenauigkeit des Klebestreifens, teils weil er ja schon einseitig klebt. Es ist auf jeden Fall hilfreich das AppleWatch-Gehäuse vorher zu fixieren. Ich werde diese Methode nicht ein weiteres mal anwenden, sondern das nächste mal flüssigen Kleber aus der Tube (E-8000 oder vergleichbares) verwenden.

BjoernImNetz -

These things are garbage! I’ve replaced the adhesive on 4-5 Apple watches with various cheap Amazon adhesive products. The tab came off on two different ifixit adhesive kits. The first one the white backer would come all the way off the adhesive, so it was worthless. The second one either stretched or was made too long.

Don’t waste your money. Quality is poor

the.thams -

Schritt 5

Verbinde den Akku wieder, wie es in der vorherigen Anleitung gezeigt wird.
Entferne den Schutzfilm vom Klebestreifen.

Don’t expect the adhesive strip to follow the edges of the watch’s case. If you try to fit it on the edges on one side, you may end up coming up short on the other, as the above image illustrates. Just try to place it slightly off the edges. It will be ok.

Vangelis Angelakis - 19/05/21

Schritt 6

Richte den Bildschirm gerade aus und drücke ihn auf dem Klebestreifen fest.
Damit sich der Kleber besser verbindet, kannst du das Display mit einem iOpener erwärmen. Übe dann ein paar Stunden lang Druck darauf aus (du kannst es zum Beispiel über Nacht unter ein oder zwei schwere Bücher legen).
Alternativ kannst du auch Display-Schraubzwingen verwenden, um den Kleber sauber anzubringen.

Buy two clamps, thank me later. Books are good but trust me the clamps are way better. Also expect the screen to wobble ever so slightly after, since the adhesive seems to be a bit elastic in nature.

Avoid hot or even warm showers to avoid causing the screen to detach from the adhesive.

Vangelis Angelakis - 19/05/21

Tinte & Feder

Dominik Schnabelrauch

Mitglied seit: 23/11/16

167812 Reputation

6 Kommentare

Will the new adhesive be water proof?

or will the watch after replacement no longer be water proof?

fredrik.liljeroth - 19/12/18

The Apple Watch isn’t waterproof, but water resistant. After opening and resealing it there is no guaranty that the resistance is the same as before. More on that topic can also be read on Apples website (“Apple Watch can't be rechecked or resealed for water resistance.“). But when resealed properly (using heat and pressure without damaging the force touch gasket in the opening process and cleaning off old residue) there shouldn’t be any concern for a normal daily use like washing hands or taking a shower. It might even work for a swim in a pool or an ocean, but I wouldn’t count on that 50M ISO rating ;)

Tobias Isakeit - 19/12/18

This one was a bugger! Dang…getting this over the display w/o sticking to everything is an exercise puzzle. The first one also didn't release correctly and I ended up installing just the blue adhesive backing…then realized that the adhesive was still on the other backing, which I then had to very carefully remove with a tweezers, then navigate the puzzle of an exercise getting it over the display and in to position. I did it, but as other commenters noted, it is not sealed anything like it originally was. In fact, it came up in a few days and I had to use the iRemover to heat it back up and press it back into place. I also use an iWatch bumper guard all the time now to protect it from popping off. For this older series 2 iWatch I’m ok.

Thank you iFixIt for top notch parts, instructions and tutorials. I’ve been an IT tech/specialist for many years, but still approach new repairs with caution, especially on Apple products, until I’ve done it at least once.

Erica Rogers - 01/06/19

Yes, resealing the Apple Watch is a tough one. It is either disconnecting the display and go without the "exercise puzzle" but risk damaging cables and having to reconnect the display vs. keeping a steady hand and feeding the adhesive around the display.

I edited the guide to apply pressure on the closed watch for a longer time now. A few hours under some heavy books might do a better job.

Oh, and congrats on the repair.

Tobias Isakeit - 03/06/19

Adhesive gasket/strip did not fit. It was slightly undersized :( I ended up cutting tiny strips to fill the gaps. :(

kamilgoslawski - 06/08/19

horrible adhesive. in trying to remove the strip, the tang holding the strip broke off. in trying to remove the strip without the tang, the strip broke in half. and worse got tangled. I had to jam the strip into the watch as best as I could but doubt if this will hold the watch together. even worse, it is not clear at all as to how to get the strip from the adhesive so I had to guess. don’t buy this product

bob bulliard - 01/03/21