Asus K53E-BBR7 Motherboard Replacement

Geschrieben von: Matthew Molina
  • Kommentare: 5
Asus K53E-BBR7 Motherboard Replacement

Schwierigkeitsgrad

Difficult

Schritte

14

Zeitaufwand

15 - 25 Minuten

Einleitung

If your laptop is failing to boot properly, your motherboard may be to blame. Replacing your motherboard using this guide will ensure that your laptop operates successfully.

  1. TuvZPQREqDFOpOCL
    TuvZPQREqDFOpOCL
    kGyUSNnf1RwSZCLM
    4FKP6vsVYjEJY51N

    • Turn off the computer and disconnect the charging cable from the laptop.

    • Push the two locking mechanisms at the top of the laptop outward and pull the battery away from the laptop.

    • This laptop is missing the battery.

  2. KUa2UPWjNIpdubJI
    KUa2UPWjNIpdubJI
    QreZOLrARLrlDtRd

    • Remove the two black 7.0 mm Phillips #0 screws on the back panel using your Phillips #0 screwdriver.

    • Using your hands, slide the cover downwards and remove it from the laptop.

  3. hNBQHRmFxVgoGICB

    • Using your Phillips #0 screwdriver, remove the four 7.0 mm Phillips #0 screws that are securing your hard drive into place.

    • Gently lift the hard drive out of its case using your hands.

    • This device is missing the hard drive.

  4. QnAiFmJEHUkfGrUh
    QnAiFmJEHUkfGrUh
    wIJGE1KLCSm2QqVL

    • Remove the following seventeen screws from the back panel of your laptop using your Phillips #0 screwdriver:

    • Sixteen black 7.0 mm Phillips #0 screws.

    • One black 4.0 mm Phillips #0 screw.

    The two screws nearest to the rubber pads are larger in diameter than the others.

    Also, you need to disconnect the antenna wires from the wireless card.

    John Harrington -

  5. crWCkhfEtAQC3wkk
    crWCkhfEtAQC3wkk
    fsmwarP5OsOJSJqy
    B6m2SxR5cTX2VRkw

    • Using the blue prying tool, separate the keyboard from the palm rest by inserting the prying tool into each of the five tabs at the top of the keyboard.

    • Slowly remove the keyboard by gently pulling the keyboard away from the palm rest.

    • A silver ribbon cable is connected to the keyboard and the palm rest of the laptop. Removing the keyboard quickly may tear the silver ribbon cable, causing harm to your device.

    On a BBR1, which looks identical to the BBR7, the blue Ifixit prying tool is slightly too wide, at both ends, to fit in the tab slot. The Ifixit black spudger does fit. Don’t try to pry the keyboard up. Put the spudger in the slot and press down and back towards the screen. The keyboard should lift out easily. It doesn’t snap out.

    John Harrington -

  6. omRsfFJEvXZaFkkh

    • Using your fingers, slowly remove the silver ribbon cable from the laptop by disconnecting it from its connector.

    • Be careful when removing the ribbon. Pulling carelessly can cause damage to both the ribbon and the laptop.

    Slide black bar on connector toward cable to release it.

    John Harrington -

  7. QPqTpEYlOHVSjNYB

    • Remove the six silver 6.0 mm Phillips #0 screws using your Phillips #0 screwdriver.

    My K53E had 7 screws in this step - one on either side of the smaller ribbon shown in step 8. And they were black, not silver.

    Don Mosley -

  8. SMIHTWrcJAQVTVBe
    SMIHTWrcJAQVTVBe
    hfQsMHCCdIp5yCet
    uwv3C1IJAAiaHioZ

    • Use your fingers to gently disconnect the following cables from your laptop:

    • Power button cable.

    • Touchpad cable.

    Lift the black bar on each connector with a pointed tool such as the pointed end on the Ifixit spludger before pulling the cable out.

    John Harrington -

  9. rni1N5U44C6tCdjL

    • Remove the optical drive from the laptop by pulling it to the right until it has been fully detached from your laptop.

  10. 1iDnWoEWgyPPPRYS

    • Close the lid of the laptop and flip the laptop over to access the screws located beneath the optical drive.

    • Remove the three silver 6.0 mm Phillips #0 screws from beneath the optical drive using your Phillips #0 screwdriver.

  11. hPshYsFAG3cLBFjH
    hPshYsFAG3cLBFjH
    MxVGooEfwTmPx6rI

    • Slide the blue prying tool between the palm rest and the base of the laptop to separate them.

    • Carefully remove the palm rest from your device using your hands.

  12. Tht31M4KEpyoCXBd
    Tht31M4KEpyoCXBd
    xPGQaeJDsWNCQyRG
    fJvEaDdAFNLwHfnP

    • Detach the gold video cable from the motherboard using your fingers.

    • Using your fingers, detach the speaker cable from the motherboard.

    • Slowly lift the blue tape from the motherboard and remove the i/o board cable.

  13. ha1kJFOVeMHYJNQh
    ha1kJFOVeMHYJNQh
    SyRHCpHraEYvyO2m

    • Remove nine 7.0 mm Phillips #0 screws from the motherboard using your Phillips #0 screwdriver.

  14. SGLN1yqnqXyLQtLa
    SGLN1yqnqXyLQtLa
    ZPHYlEoQUXytNZcj
    2y5IU1ubVNKQ4g23

    • Use your hands to lift the motherboard from the laptop.

    • The fan and several ports will be attached to the motherboard when it has been detached from the laptop.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Matthew Molina

Mitglied seit: 26/10/16

253 Reputation

0 Kommentare