Asus ROG G750JH-DB71 Fan Replacement

Geschrieben von: James Mills
  • Kommentare: 0
Asus ROG G750JH-DB71 Fan Replacement

Schwierigkeitsgrad

Difficult

Schritte

13

Zeitaufwand

45 Minuten

Einleitung

This guide covers how to replace the fan for the Asus ROG G750JH-DB71.

The fan provides cooling for all the internal components. After long term use of the laptop the components start to heat up. The fan will turn on a remove heat from inside the laptop. If your laptop is experiencing overheating after extended use, consider replacing the fan.

Before replacing the fan, inspect it, look to see if there's any buildup of dust or debris keeping the fan from working. If this is the case clean the fan with a cloth, cotton swab, or whatever you prefer. Make sure to also check the vents on the exterior of the laptop for any dust or debris.

  1. yD4CrxAF4gjTGslC
    yD4CrxAF4gjTGslC
    doOgxPDUWNcbrClC

    • Ensure the laptop is powered off and unplugged before beginning.

    • Flip the laptop over so the bottom case is facing up.

  2. V4sRRH3gTiMHqGpL
    V4sRRH3gTiMHqGpL
    pL5bLRheYDP5HZdP
    ddvlyVyPAP5UjqoE

    • Push the switch near the front of the laptop to release the battery from the computer.

    • Pull the battery out and away from the center of the computer.

  3. NJYIKShvJkyWxUGH
    NJYIKShvJkyWxUGH
    GXniwh2VMHAE3RKv
    CLSAaIMJRnKgtUvY

    • Use a spudger or your finger to lift up the plastic cover on back of the laptop.

    • Under the plastic cover is a captive screw; unscrew it using a Phillips #00 screwdriver.

  4. vUGwprAJEKPYog2y
    vUGwprAJEKPYog2y
    bKecKNvwJkRFLfJB

    • Remove the cover.

    • If your goal is to replace/remove only the hard drive. You don't have to complete the following disassembly steps and can go on to the hard drive replacement guide.

  5. UWsqSmC1QcXDDUXg
    UWsqSmC1QcXDDUXg
    UdTHBqNARiZRZKEI
    uYCSHrBonKQNovGQ

    • Remove the hard drive by unscrewing the 4.4 mm Phillips #00 screws.

    • Remove all of the plastic caps around the edges using a pick or flathead screwdriver, and remove the screws underneath them. (one 13 mm Phillips #00, six 8 mm Phillips #00)

    • Remove all of the screws underneath the cover removed previously. (six 8mm Phillips #00, three 1 mm Phillips #00)

  6. EMaqul61UI4NHyYf
    EMaqul61UI4NHyYf
    ZVYR4eTHd6KPtaYq
    WY5xWCTdqN6LYSei

    • Push on the metal tab with a flathead screwdriver or an iFixit tool to remove the CD rom. It is located below a previously removed screw.

    • Do not pull the CD rom out from the side before pushing the metal tab as it will only damage the cover.

    • Remove the three (4 mm Phillips #00) screws that were previously covered by the CD rom.

  7. SgTtAMgdGCHTfjpf
    SgTtAMgdGCHTfjpf
    MEVufdLxECcmylFi
    J5UBYBTdAekgaCOx

    • Once the screws are out and the CD rom is removed, the back cover can be taken off by hand.

    • Disconnect the speaker cables located in picture 1 and 2.

    • Remove two 8 mm Phillips #00 screws on each corner shown in picture 3.

  8. 1wOdXKyNRYFQH1UT
    1wOdXKyNRYFQH1UT
    SZhNe2bXcjpTvlhg
    dV4ZhwqGDpWgRgrk

    • Pry the keyboard gently using the iFixit prying tool.

    • Make sure to unhook the cables and wires from the keyboard gently in Picture 3.

  9. EuKQn1L2iChNdFyM
    EuKQn1L2iChNdFyM
    i3eewCn4ARqEJuio

    • Now you can pull the keyboard off but make sure to do so carefully without damaging or scuffing any components.

    • Pull up and out at an angle as to avoid damaging the internals of the laptop.

  10. BUUWVJMUA1tvB4CK

    • Remove the Data and Wi-fi cables from the sockets shown.

  11. Q3LbSCxwImVgOuXq
    Q3LbSCxwImVgOuXq
    ybQHWoNkhwZOo5yX
    Mgke66A6DTsTJ3sd

    • Slowly close the lid and turn the device around.

    • Remove the 6 screws (3 on each side) from the edges of the device. (8mm Phillips 00)

    • Remove the Webcam cable.

  12. VJG4BNScoLWZUfnB
    VJG4BNScoLWZUfnB
    SlrmKkPoFIXH6rrI
    14mYtUWmdocWlAHG

    • Carefully lift the lid away from the rest of the device.

    • There may be tape covering the fans or other components. Remove it slowly as to not damage anything.

  13. EJNCENEXFw1bhrdJ
    EJNCENEXFw1bhrdJ
    lfCxadlqqIO1lDpE
    NtA6MsDKujkxYRhM

    • Remove the three screws surrounding each fan shown along with the ribbon cables connecting them to the motherboard. (4mm Phillips 00)

    • Remove the USB port board blocking the rightmost fan.

    • Remove the fans from the board.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

James Mills

Mitglied seit: 25/10/22

471 Reputation

0 Kommentare