Asus VivoBook E203MA-TBCL432B Motherboard Replacement

Geschrieben von: Brad
  • Kommentare: 5
Asus VivoBook E203MA-TBCL432B Motherboard Replacement

Schwierigkeitsgrad

Moderate

Schritte

13

Zeitaufwand

25 Minuten

Einleitung

If you find that you need to replace the motherboard on the Asus VivoBook E203MA-TBCL432B, this guide will help you access it. This replacement requires only a standard Phillips #0 screwdriver and a plastic opening tool. The screwdriver is used to remove the screws on the bottom panel of the laptop and the screws connecting the battery and motherboard to the laptop. This is a simple replacement and should not require any additional knowledge or information.

  1. 1uyiBS1mXaok3pxN

    • Position the laptop so that the bottom panel is facing upwards, the hinge is away from you, and the ASUS logo is against the table.

    • It will be easier to replace the battery if the laptop is closed.

  2. FowyaxcPWE2CVcoF
    FowyaxcPWE2CVcoF
    PjCNHESVVkaEPBIa
    nF1AGpjIMZPhdSth

    • Use a Phillips #0 screwdriver to remove the eight 5 mm screws on the back panel.

    • Remove the two 7 mm Phillips #0 screws.

    • The 8 screws marked in red are all of the same length, 5 mm, and should not be interchanged with the two longer 7 mm screws marked in orange.

  3. QMvdGrZX1TwLFiEy
    QMvdGrZX1TwLFiEy
    fKlcYakDAM4sYMt4
    qCYXLEEYNREebQjr

    • Insert the iFixit opening tool in between the back panel and the rest of the laptop.

    • With the iFixit opening tool, lift the panel from the laptop body. Work your way around the device creating separation with the tool.

    • Once there is enough separation between the back panel and the device, gently pull off the back panel with your hands and completely remove it.

    • Make sure to use a plastic tool, not a metal one, so that you don't scratch the panel.

  4. uVxFslYYN3425GXF
    uVxFslYYN3425GXF
    5XxQhZCqOCLg1eWw
    dGMiT3lGIQEgkTJR

    • Now that the back panel is removed you can clearly see the battery and all of its connectors.

    • Begin by removing the silver ribbon cable along the back of the battery.

    • To disconnect it from the motherboard, lift the black tab on the Zero Insertion Force (ZIF) connector up and pull the cable away using the blue tab.

    • Disconnect the ribbon cable from the left side in the same way.

  5. Hd4TiZwBotYTAlDA

    • Remove the red and black wire along the bottom of the battery.

    • This does not need to be disconnected, only removed from the clamps along the bottom of the battery.

    this is the audio cable.

    Andriux Corrales -

  6. xbjUQCVQuvYhxGsD
    xbjUQCVQuvYhxGsD
    TL4JPI3IwTEnUt5e

    • Using the Phillips #0 screwdriver, remove the two 3 mm screws located at the top and left side of the battery.

    To discard battery damage, disconnect the battery and try to power on the notebook using only the power cable connected. Maybe the power button is the cause of bad working.

    Andriux Corrales -

  7. 32OyWUAvZfCHigQE
    32OyWUAvZfCHigQE
    ZhwdJoCUKlfRXMIV
    eG1HIyGhYVHvATNp

    • Gently lift the battery being mindful of the one cable still connected to the motherboard.

    • With the battery lifted, pull the remaining connector going to the motherboard up, it should come out with little force.

  8. bG2l31PYUg1ZhUnk

    • Disconnect the small black and red bundled cable by lifting it directly up from the connector on the motherboard.

  9. XjxReH5LscaeH5OV
    XjxReH5LscaeH5OV
    yxGeXXU5GwwvIUZ5

    • Disconnect the black ribbon cable in the center of the motherboard by first lifting the black tab and then pulling the cable free.

  10. BnEUGT6CKrIlwVx4
    BnEUGT6CKrIlwVx4
    ZRWbZoSL1fH5kMqI
    jCNVOeSIlRTOSZhw

    • Remove the coaxial connector from the motherboard.

    • Grasp the wire close to where it connects to the motherboard.

    • Pull up and away from the motherboard until the connector is no longer attached to the motherboard.

    this is the antenna cable for wifi signal. When it's not working, is not possible to replace the wlan drive because it's integrated to the motherboard. You need disconnect the connector and use a wifi adapter trough usb connection.

    Andriux Corrales -

  11. MJgvZUXYHARSoH2Y
    MJgvZUXYHARSoH2Y
    m6fe1Hnf3BLUaLuT

    • At the top of the motherboard there is a connector that is taped in place.

    • Peel back the tape so that it is no longer in contact with the motherboard.

    • Gently pull the connector out from its socket.

    this is the video connector. Some times replacing this flex can be the solve to LCD problems. First at all, check video signal connecting HDMI monitor and reinstall video drivers to discard physical damage on video components.

    Andriux Corrales -

  12. WxAAPgQY2YnDTGjA
    WxAAPgQY2YnDTGjA
    X3NQxoMNR6PXGfSG

    • Now that all the cables are disconnected from the motherboard, you can begin to remove the screws holding the motherboard in place.

    • Use a Philips #0 screwdriver to remove the six 2 mm screws.

  13. XU4iUpMeIRNuxpyx
    XU4iUpMeIRNuxpyx
    uv4kLYnt21YLsIWO
    Mx5cQhwQVRtDmY4v

    • Lift the motherboard away from the computer while allowing the ribbon cable in the middle to fall through its cutout.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Brad

Mitglied seit: 20/03/19

443 Reputation

Ein Kommentar

Can we have a tutorial on how to remove the storage from it?

CJ-1-2-3 -