Einleitung

  1. 3GK1ZtNGcXBdlORW
    3GK1ZtNGcXBdlORW
    AVqjLuSyLLujDMny
    • Place the phone on a flat surface with the screen facing down.

    • Remove the plastic backplate by pulling up on the bottom of the cover.

  2. OnxOFo3fUxEltAVu
    • Remove the battery by pulling up from the top of the battery.

  3. kUHpSfDt21PgBZNI
    kUHpSfDt21PgBZNI
    nArILyJvpGYCqB6J
    • Remove the two screws midway up the phone on the left and right sides using a T6 Torx Screwdriver.

    • Warning: One screw will have warranty tape covering the screw. Removing this screw will likely void the phones warranty.

  4. SPZxgG22AmQVhsiL
    SPZxgG22AmQVhsiL
    RCeBWQVnvbIeKx3C
    • Flip the phone over so the keyboard faces up.

    • Insert a plastic spudger into the screen where speaker resides.

    • I recommend going from the side. There are two layers to the cover. You need to make sure you get underneath the bottom layer if you plan on reusing this cover.

    • Gently lift up plastic screen cover until screen cover separates from screen.

    • Continue until screen cover is completely removed.

  5. URVTqDZJHFF6sVBM
    URVTqDZJHFF6sVBM
    HQdIPNA11RETPLob
    FtEfHaNrUDI2UDZk
    • Insert the spudger into the top of the plastic siding on the front of the phone and lift up until the siding lifts up.

    • Slide the tool around the entire perimeter of the phone until the plastic siding is completely removed.

  6. MaeRhVM6XwX2VtPR
    MaeRhVM6XwX2VtPR
    dvngfsqceRIPsKFO
    • The keyboard should slide off of the phone now that the plastic siding has been removed.

  7. jbQcuyuoYFKg2UwC
    jbQcuyuoYFKg2UwC
    g2PcARMGFiHmgvM2
    HYUAdJVCOMTfbSkn
    • To detach the screen, there are two screws at the top of the phone to be removed. Use the T6 Torx Screwdriver to remove the screws.

    • There is a gold ribbon on the top left of the phone. Lift up this ribbon gently until it is detached from the phone.

    • Note: When reassembling, the ribbon should be reattached before replacing the top screws.

  8. Td6yTvrnTNfACxNy
    Td6yTvrnTNfACxNy
    nyeKvDmDAciK1pBu
    IY4JXJRDSZwwP3kw
    • There are two clips on each side of the phone. Insert a plastic spudger between the clips and the screen.

    • Use pressure to unlatch the screen from the clips.

    • Now that these clips have been undone, the screen should lift up easily.

  9. EALNFqphty2xBAWY
    EALNFqphty2xBAWY
    N6Sv4RX6KT5xT1gx
    • Now there are four screws that need to be removed. They are located at the bottom of the phone and can also be removed using a T6 Torx Screwdriver.

  10. NXKy1UrY2DQvyGNc
    NXKy1UrY2DQvyGNc
    FAH6tXQZODMAGKln
    OPOOG2yFNOy4vnPV
    • Now the motherboard will lift up out of the plastic backing of the phone.

Cory Davis

Mitglied seit: 20/04/11

503 Reputation

0 Kommentare