Blackberry Bold 9650 Faceplate Replacement

Geschrieben von: Ryan
  • Kommentare: 2
Blackberry Bold 9650 Faceplate Replacement

Schwierigkeitsgrad

Moderate

Schritte

13

Zeitaufwand

15 - 30 Minuten

Einleitung

Use this guide if your Blackberry Bold 9650 faceplate is cracked, broken, or has any other form of damage that calls for a replacement. Faceplates are used to protect your phone by covering its exterior, so it is important that you replace it when it is no longer able to provide that protection. There are four prerequisite guides to follow leading up to this guide—all of which are included in these instructions.

  1. eNLu4FDCTjH2fArt
    eNLu4FDCTjH2fArt
    PXODXZSxTlMl6MgI

    • Turn the device upside down.

    • Using your finger, slide the silver cover release button towards the top of the device.

    • Lift and remove the back cover.

  2. BOKXSEakaW3J3Hsj

    • Using your fingernails, lift the sides of the battery.

    • Remove the battery.

  3. TEGrbhClPSs1bMCE

    • Orient the device so that the screen is facing the ground.

    • Using your finger, gently lift the top of the SIM card.

  4. KrKWOtJdIjmyiEeG

    • Gently pull out the SIM card.

    • The card will break in half if you apply too much force when pulling out the card.

    make sure to takeout memory card also.

    Trying to open the back part with card still installed is a BIG NO NO.

    ralph -

    I ordered a new speaker and as soon as it came it I jumped on here to look at the directions. followed the directions exactly and now it works again. Only suggestion is to be careful removing ear piece cover, there are 4 small fragile plastic prongs at the top that can easily break. I broke 2 but phone still works! Thanks for the help!

    Jeremiah Croych -

  5. yUM5IBAnhQFcHfap

    • Using a T6 Torx screwdriver, remove the four screws from the bottom half of the device.

  6. MmWGDV3j5JxIKTMc

    • Orient the device so that the screen is facing you.

    • Using a spudger, remove the ear piece cover.

  7. bCVuTiUQlBcLZOJ4

    • Using a T6 Torx screwdriver, remove the two screws from the top corners of the device.

  8. TWFApOw4VqXi3WaG

    • Remove the back chassis by gently pulling the chassis back and forth.

    • The headphone jack can break if the chassis is pulled too forcefully.

  9. vnmZxCFFfSfAekHs

    • Orient the device so that the screen is facing the ground, and the top of the phone is facing you.

    • Using a pair of tweezers, lift and remove the following:

    • The two round connectors on the top of the mother board.

    • The round connectors are hooked into the mother board.

    • The flat connector in the lower corner of the mother board.

  10. mV4kQaUMOVWxHicQ

    • Using your fingers, carefully lift and remove the mother board.

    • The connectors underneath the mother board are delicate and easily damaged.

  11. MXgBwQ2NhSRWVVHI

    • Using a pair of tweezers, remove the three ribbon connectors.

  12. ARkSvs6SZENVFYbS

    • Remove the mother board by lifting the board upward.

  13. LHTvrk2cmpKyTKbc
    LHTvrk2cmpKyTKbc
    P2LvvwENGgp1oEpj

    • Using a pry tool, lift up on the four tabs located on the edges of the faceplate.

    • Remove the faceplate by lifting the plate upward.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Ryan

Mitglied seit: 12/03/12

663 Reputation

0 Kommentare