Canon EOS 40D Shutter Button Replacement

Geschrieben von: Kenadie Buccellato
  • Kommentare: 4
Canon EOS 40D Shutter Button Replacement

Schwierigkeitsgrad

Difficult

Schritte

18

Zeitaufwand

1 - 2 Stunden

Einleitung

If your Canon EOS 40D camera’s shutter button is sticking or not working properly, use this guide to replace the shutter button.

A functional shutter button is necessary for any photographer to capture their work. Over time, the shutter button on a camera may become damaged or broken. If you notice your shutter button sticking or it is unable to function, consider replacing it for optimal use of your Canon EOS 40D.

Before using this guide, assess your shutter button for any trapped debris. Shutter buttons often become stuck when dust and grease gets trapped inside. A simple cleaning will oftentimes fix this issue without needing to replace the shutter button.

In order to complete the replacement, the front, back, and top coverings of the camera must be disassembled in order to access the shutter button.

  1. gTDhDdcs1XMwVj3t

    • Locate the battery compartment cover on the bottom of the camera below the shutter button.

  2. FdjJdG4uRgXCLJYU

    • Find the marked arrow on the battery compartment cover labeled "BATT. OPEN". Slide the lever following the arrow's direction and lift at the same time to release the latch.

  3. dKOYUmyxPSLGl6yX

    • Release the lever and allow the battery compartment cover to completely open.

    • Remove the battery.

  4. sXaNq2EOOHYW2JCO

    • Peel off the grip material from the body of the camera, exposing the screws.

  5. CBxsH3HqLAZyYdUb

    • Remove the rubber eyepiece by sliding it upwards.

  6. HOehX236F3NVElMK
    HOehX236F3NVElMK
    GLJKEIDa3XitfQNm

    • Remove the three 5.0 mm Phillips #000 screws.

    • Remove the single 12.0 mm Phillips #000 screw.

    Notice that the screw next to the strap loop also has to be removed in order to remove the top cover in step 16

    Simon van den Broek -

  7. mHdBOnxMIAUnOimn

    • Remove the two 3.0 mm Phillips #000 screws on the bottom of the camera.

  8. DY6UWAwcO3usAAVp
    DY6UWAwcO3usAAVp
    f6OaWYjUMQQZdPlx

    • Remove the side cover using a plastic opening tool or your hands.

    • Use a plastic opening tool to gently start prying the rear case up from the rest of the camera.

  9. cP51QcNuFIPF4O1E
    cP51QcNuFIPF4O1E
    i4M2N6O1swuhVKOX

    • Use the tip of a spudger to disconnect the ZIF connector on the left side of the camera.

    • The ribbon cable on this device was torn in the process of removing the back case, so there are no photos showing this step.

    • Disconnect the ribbon cable securing the rear case to the motherboard.

    • Separate the rear case from the camera.

  10. lJQT1LoZlWGNJcQp
    lJQT1LoZlWGNJcQp
    FdTouBsbODHuCA3v
    ISAVojZV6KOqAhEU

    • Remove the five 3.0 mm Phillips #000 screws.

    • Remove the two 5.0 mm Phillips #000 screws.

    • Remove the single 3.0 mm Phillips #000 screw.

    • Remove the two 5.0 mm Phillips #000 screws.

  11. PgUcVJ1RATShW2Ss

    • Pull off the cover.

  12. TiAYsxx6QAFa6JG4

    • Use a plastic opening tool to flip up the black retaining flap on the ZIF connector.

    • Pull the ribbon cables free of the connectors.

  13. UkSMa1sSlDCDLFrE
    UkSMa1sSlDCDLFrE
    KFriTnjw6t1gw15R

    • Remove the side panel by unscrewing three 5 mm JIS #000 screws.

  14. fqPgZT3AKZsOplVF
    fqPgZT3AKZsOplVF
    LLRpQWAVSHnDncHC

    • Remove the two 5 mm screws from under the wheel and under the shutter button using a JIS #000 screwdriver.

  15. e2ABT12fg5I1PM6h
    e2ABT12fg5I1PM6h
    imUUO3AKnAdTOfMA
    gLHphSyKQHQCSRSF

    • Remove the red and yellow plugs from their sockets using the plastic opening tool.

    • Position the tip of the tool under the raised plastic line, then push up.

  16. UkgGewNQVv31PEMR
    UkgGewNQVv31PEMR
    EudoWDqoNj6mZ5KY
    TefLPfCbPaGIwdOW

    • Remove the cable running from the top of the camera to the black and white box.

    • Use a pair of precision tweezers to poke through the rubber coating and create a path for the wire to slide out.

    • Disconnect the wire by sliding it away from the rubber.

    Does anybody know the purpose of the black and white box?

    Rad Fahrer -

  17. XtxdUmFqGlTmNxUo

    • Use a Phillips #000 screwdriver to remove the two 5.0 mm screws and single 7.0 mm screw.

    • Notice that one is screwed in from the side.

  18. jrYXdPYZcYcqfdEp
    jrYXdPYZcYcqfdEp
    vQjWa1ifVKxlL2S6
    AEUPakdhWjKUNRkt

    • Once the screws are removed, wiggle the piece out of its socket and flip it over, exposing the shutter button.

    • Use tweezers to separate the piece from the ribbon that it is glued to.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Kenadie Buccellato

Mitglied seit: 03/09/15

405 Reputation

2 Kommentare

Thanks for these instructions. I've successfully replaced the shutter button assembly on my Canon 50d using this guide.

William Eggers -

Thank you for the tutorial. I don’t know how to replace the button. Which glue to use ? Must it scratch the connections on the flex circuit before gluing the new button ?

Tony -