Canon EOS Rebel T5 Motherboard Replacement

Geschrieben von: Austin Tucker
  • Kommentare: 6
Canon EOS Rebel T5 Motherboard Replacement

Schwierigkeitsgrad

Difficult

Schritte

14

Zeitaufwand

25 Minuten

Einleitung

If you find that your camera's motherboard has failed, and needs to be replaced, this guide will show you the steps necessary to complete this task.

  1. JZpuhYn5aNx2a5k5

    • Lay the camera on its back so that the card/battery door is facing you.

    • Using your fingernail, slide the tab on the battery door up to release the battery door latch.

  2. ImYNPluw4SOitEDE

    • Lift the now free card/battery door to reveal the battery compartment.

    • Push the gray lever to the right side so that the battery can be removed and replaced with a new one.

  3. pL6vROgghEGJB2p2

    • Turn the camera so that the back is facing to your right.

    • Remove the 5mm Phillips #000 screw above the rubber USB port cover.

    2 more screws behind rubber cover.

    Michael Gill -

  4. QCLgfQBmWFJQQwmh

    • Remove the rubber piece.

    • Unscrew the two screws under the rubber cover to completely remove the rubber cover piece.

    • It is held in place by a notched tether, but can be easily manipulated to slide out.

  5. rInTocWZnrQMjULP

    • Turn your camera so that the bottom is facing you.

    • Remove the 5mm Phillips #000 screws.

    There is a 6th screw next to the battery door.

    Michael Gill -

  6. ISEoqXlHElNZTyxX

    • Now turn the camera so that the front is facing towards your right.

    • Remove the two remaining 5mm Phillips #000 screws.

    Instructions are forgetting the two screws on either side of the viewfinder…. Viewfinder slides up to reveal two screws.

    Hugh Morand -

  7. MsAeFqtNGjb34bSj
    MsAeFqtNGjb34bSj
    f64UqWVwpAtPgpEo
    A33ZdIWoKkStvY3V

    • Now that all of the exterior screws have been removed, grip the camera firmly on both sides.

    • Gently pry the back panel from the main body of the camera.

    • There are two ribbon cables that need to be removed in order for the back panel to come free from the camera body, as indicated.

    • This back panel contains various control components of the camera as well as the LCD screen.

    Do NOT pry until you’ve removed the eye gasket, and the 2 screws behind this! You will break the camera.

    Michael Gill -

  8. E3xJNDcNIWcW65NV

    • Remove all ribbon cables with the plastic spudger.

    • Gently pry up the black plastic tabs to slide out the ribbon cables

  9. bwY4L1ruPBK2m1jF

    • Turn your camera so that the top is facing you.

    • Remove the two black 5 mm Phillips #000 screws.

  10. iR5eTXmhxmFrsCxF
    iR5eTXmhxmFrsCxF
    HsM1vLY1VtQOefip
    RPe5ZDjWMFc1qgpo

    • Turn the grip side toward you.

    • Remove the rubber grip, using the plastic spudger.

  11. c4cl6nOrrMoj12Xm

    • Remove the black 5 mm Phillips #000 screw, located under the grip.

    they is a cable i think gray in color on the top panel, where does it fit, it seems to come out easily

    Tshepiso Marques Molefe -

  12. jlDlMIYOoKcKYTnC

    • Remove the top panel of the device.

  13. ugfNSgnwDxFjmyi2
    ugfNSgnwDxFjmyi2
    gNem1Hd3xWCXO2xM

    • Remove the front panel of the camera.

  14. boa6RZLDuDIAb2FR
    boa6RZLDuDIAb2FR
    cN3PYQ6qSyovMSAv
    OFWsUITrSB6laMmi

    • Remove the five silver 5mm Phillips #000 screws.

    • The motherboard can now be removed.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Austin Tucker

Mitglied seit: 28/08/15

1003 Reputation

Ein Kommentar

This guide is amazing, but if you change the mainboard do you have to initialize it by software, like Spt?

Edgar Nunes -