Einleitung

The lens is essential in any camera. Any flaw in a lens will ruin a cameras ability to operate. This guide will detail the steps required to replace the camera lens for a Canon Powershot G7X.

  1. Ccq5sO4fdVBqCdH3
    • Remove the five 2mm Phillips #000 screws that are under the screen of the camera.

    Only 3 screws

    Dufour -

  2. jEKXOHOKAklPvpnW
    • Remove the two 3mm Phillips #000 screws under the AV-out digital flap.

    • Remove the two 3 mm Phillips #000 screws from the side of the camera.

  3. 1iwfloUmeWpaeKGi
    • Remove the two 3 mm Phillips #000 screws on the side of camera with the flash toggle.

  4. a4hAlYYjXZYEjNXG
    • Remove the four 4 mm Phillips #000 screws from the plate on the bottom of the camera.

  5. iI1NGuIDwmfEtdFV
    • Remove the back plate.

  6. 1tkoeGBMOu111ZfP
    • Remove the three 3 mm Phillips #000 screws around the dial.

  7. 4k2GKfLKH2La2YIL
    4k2GKfLKH2La2YIL
    pNPyDlW2oKCBN5KW
    • Using the nylon spudger, gently lift the ZIF tab.

    • Disconnect the ribbon cable that connects the dial to the motherboard.

    • Remove the dial from the device.

  8. UdWecZ1BXCNpMTwu
    UdWecZ1BXCNpMTwu
    VILGfdJJUXBWbeNi
    • Remove the three, blue 5 mm Phillips screws from the back plate.

    • Remove seven 2 mm Phillips #000 screws.

  9. hSaSbw2OD6rOeJBq
    hSaSbw2OD6rOeJBq
    qpbjP3TRZFLybiNx
    • While using the plastic opening tool, gently pry the top plate off the camera.

  10. kHT3tQ35XBd6w56X
    kHT3tQ35XBd6w56X
    jxBsMIMpcZVeMHyR
    • Using the black nylon spudger, gently lift the ribbon cable connected to the LCD screen housing until it comes out then remove the housing.

  11. MC1UVmeYBEYOfKLC
    MC1UVmeYBEYOfKLC
    NID1QGAJX2VOuIQB
    • Remove the 2 mm Phillips #000 screw underneath the top plate.

    • Remove silver plate.

  12. VGNjiWZEk2nkb1gV
    • Take the Phillips #000 and remove the three 5 mm screws from the front plate.

  13. AlLZtGdfFHvKKwN2
    AlLZtGdfFHvKKwN2
    CPIfkcE2fohLlIkJ
    • Using the spudger, gently lift the ribbon cable from underneath the front plate.

    • Remove the front plate.

  14. Zebxfv21jwREj46b
    Zebxfv21jwREj46b
    e2RZXRncMhXLuMHq
    • Remove flash toggle plate.

    • Remove the 2mm Phillips #000 screws under the flash toggle.

  15. bNkPx6b4XWIMsr65
    bNkPx6b4XWIMsr65
    Q5RACI3JD4dEdBRO
    • Flash contains charged capacitor. Shock hazard.

    • Using the black nylon spudger, gently lift the ribbon cable that connects the flash to motherboard and remove the flash from the device.

  16. PVQVV1YqujSQWDRD
    • Remove the 5 mm Phillips #000 screw from the copper plate.

  17. yGDlZ5UXL6Ib1TVe
    • Using the black nylon spudger, lift the ribbon cable gently until it comes out.

  18. gtfcKD4QwTADQdJH
    • Remove the copper plate to reveal connections to the lens.

  19. UEaYxGhotJyQS1l2
    • Using the black nylon spudger, lift gently on the pin connector until it comes off.

  20. msbSeVF6DNP3TR5Y
    msbSeVF6DNP3TR5Y
    NUoQTDoif6DYoCjc
    • Using the spudger, gently lift on the ribbon cable until it comes out.

    • Separate the lens from the motherboard.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Kyle Pellham

Mitglied seit: 09/04/18

397 Reputation

2 Kommentare

Not that great of step by step. Lots of missed steps and lots different screw length and thread. Over all it's just an ok guide.

Nick Thomas -

how do you tell if the lens is CCD or not

kingwayne77none -