Canon PowerShot S100 Control Dial Assembly Replacement

Geschrieben von: Ricky
  • Kommentare: 2
Canon PowerShot S100 Control Dial Assembly Replacement

Schwierigkeitsgrad

Moderate

Schritte

7

Zeitaufwand

10 - 15 Minuten

Einleitung

The control dial on the back of the camera can be removed and replaced.The control dial is used to adjust the camera's settings and navigate the camera menus.

  1. gijZvnmUXApjTuFW
    gijZvnmUXApjTuFW
    DmwinWIjgYGdJAuO
    aoC2UwTWjiEKlGpR

    • Remove the 2 screws (3.2mm, Phillips #00) found on the bottom side of the camera.

    • Remove the 2 screws (3.2mm, Phillips #00) found on the side of the camera.

    • Remove the 2 screws (3.2mm, Phillips #00) found on the side of the camera where the terminals are.

    • Open the flap revealing the cable inputs and remove the final screw (3.8mm, Phillips #00) found inside.

  2. jgr3QvUeGTwSR614

    • Turn the camera so that the LCD screen is facing you.

    • Remove the back panel by pulling it off of the camera.

  3. oAeIvIoUf3AFROWb
    oAeIvIoUf3AFROWb
    2GFdPvbXGNBDOF1F
    Xh34VWCubOFgkmfV

    • Turn the camera so that the lens is facing you.

    • Do not pull the front panel off without removing the ribbon cable first.

    • Slowly lift the front panel from the camera.

    • The ribbon cable is connecting the front panel to the camera. Using the tweezers, gently pull the ribbon cable out of its socket.

    • A spudger may also be used to remove the ribbon cable.

    • Remove the rubber guard that rests on top of the lens.

    there is a small hole in the ribbon which the point of the tweezer can hook into to remove the cable.

    macman2 -

  4. QHqtiiSPT6PPGPBS

    • Turn the camera over so that the LCD screen is facing you.

    • Remove the screw (3.9mm, Phillips #00) that is attaching the thin metal frame to the camera.

    • Remove the 2 screws (3.1mm, Phillips #00) that are attaching the control dial panel to the camera.

  5. bD3MTJk2HHmIlZFQ

    • Using the tweezers, detach the ribbon cable that is connected to the dial panel.

    • A spudger may also be used to remove the ribbon cable.

  6. ybp11MadyJoAgQ4Q
    ybp11MadyJoAgQ4Q
    Vb46vAjypqtZBMrC

    • Turn the camera over so that the lens is facing you.

    • Using the tweezers, gently lift the flap that is securing the ribbon cable to the motherboard.

    • Using the tweezers, remove the ribbon cable from its socket.

    • A spudger may also be used to remove the ribbon cable.

  7. 6ZVNuFU5BTgFBHwt

    • Turn the camera over so that the LCD screen is facing you.

    • Gently pull the control dial panel, and its attached ribbon cable, through the opening between the top panel and the camera body.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Ricky

Mitglied seit: 23/02/15

958 Reputation

Ein Kommentar

I have Canon S100 and it was stuck. Can I send this camera to you to get it fixed and if so, what is your address and how much it will cost?

Yeluchuri Paparao -