Canon PowerShot SD500 Digital ELPH Flash Bulb Assembly Replacement

Geschrieben von: Taylor Shields
  • Kommentare: 0
Canon PowerShot SD500 Digital ELPH Flash Bulb Assembly Replacement

Schwierigkeitsgrad

Difficult

Schritte

20

Zeitaufwand

15 - 20 Minuten

Einleitung

The flash bulb is essential for to take dimly lit photographs. If the flash goes out, your camera will have severely limited functionality.

  1. UQgnr14RfcD3mAyL

    • Slide open the battery cover.

    • Push the small orange tab to the side so the battery can be removed.

  2. U1AZWXVmMEtdyqtP
    U1AZWXVmMEtdyqtP
    camUGdUevG6ovB1T

    • Slide the battery out of the battery compartment.

  3. HIpHCY4njALhJl1P
    HIpHCY4njALhJl1P
    MRiPxjysjMjylFOX

    • Two Phillips screws need to be removed using a #00 Phillips screwdriver. The upper screw is under the USB port cover, which can simply be pulled away gently from the casing. the lower screw is visible on the panel.

    • The screws are different sizes. The .125 inch screw is located under the USB port cover. The 0.85 inch screw goes in the lower hole on the panel.

    • When looking at the back of the camera, these two screws are on the right panel of the camera.

  4. TACKFVnsJ4E3DV4G

    • Remove the right side cover from the camera casing.

  5. aIUQFYeQfRJNysLB

    • Remove a .07 inch Phillips screw using a #00 Phillips screwdriver.

  6. FIKCV4oAkPDSJPDl

    • Remove two .085 inch Phillips screws from the left side of the camera using a #00 Philips screwdriver.

  7. kROKnMK5mAmXtOu2

    • Remove the left side cover from the camera.

  8. wGkX1Uhkl6gjHHZE

    • Remove three .15 inch Phillips screws from the bottom of the camera using a #00 Phillips screwdriver.

  9. URBG6gRghbydhEIl
    URBG6gRghbydhEIl
    Xw1QetN1IUucrWkG

    • Once the casing is unscrewed, hold the camera with one side facing down, and lift the opposite face of the casing to open it.

    • Remove the internal camera components and layout out all pieces on a clean surface.

    • The front and back cover may require gentle rocking to remove.

  10. hg62s3KIWRWdVDv6

    • Carefully wedge the pry tool under the ribbon in the ribbon gate.

    • Gently remove the ribbon from the ribbon gate by pulling it away from the gate with the pry tool.

    • Be careful not to damage the ribbon.

  11. wEXN3jwnDwgXVnVK

    • Gently press the ribbon back to get access to a Phillips screw behind it.

    • Be careful not to damage the ribbon.

    • Unscrew two .125 inch long Phillips screws using a #00 Philips screwdriver.

  12. hcd4YPvCWB24c2Gm
    hcd4YPvCWB24c2Gm
    d5uXCjLnMGATSuZ3
    YnPYxZegW23EBlpT

    • Remove the ribbon with a pry tool by gently pulling it out of the ribbon gate tab.

    • Be careful not to damage the ribbon.

    • Pull the button board away from the rest of the camera.

  13. gHN5QWFbM6hDm3eE

    • Unscrew one .113 inch Phillips screw using a #00 Phillips screwdriver.

  14. gIkerwLYh6MdvBun

    • Lift the LCD screen up and away from the tab that holds it in place on the face of the camera.

    • Be careful, the LCD screen is still connect to the camera by a ribbon cable.

  15. yZRkUYQygq4wPR6M
    yZRkUYQygq4wPR6M
    BBlVYxyK5HTvU3ke

    • Gently press the pry tool under the ribbon gate and lift up to free the ribbon connecting the LCD to the circuit board.

    • Be careful not to damage the ribbon.

    • The LCD can now be completely removed from the camera.

  16. uJpjPjQxU5Ke1OSX

    • Arrange camera so it is facing up towards you.

    • Unscrew one .01 inch Phillips screw using a #00 Phillips screwdriver from the front of the camera.

  17. 3MSEljkNA3YwKJkh

    • Gently remove the indicated ribbon from respective ribbon gates.

    • Be careful not to damage the ribbon.

  18. tqQEyJLPSoAbSNjh

    • Place spudger under white connector and gently lift it vertically out of its slot.

    • Be careful not to damage wire connector during removal.

  19. rEEhWiKdXYBq4sqW

    • Unscrew three .065 inch Phillips screws using a #00 Phillips screwdriver from the back of the camera.

  20. xVjrgkj1IEdYBwNc

    • Gently pull away flash bulb assembly from the rest of the camera.

    • Be careful not to damage the ribbon on the rest of the camera.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Taylor Shields

Mitglied seit: 13/10/14

846 Reputation

0 Kommentare