Canon PowerShot SD960 IS LCD Screen Replacement

Geschrieben von: Kacy Ewing
  • Kommentare: 1
Canon PowerShot SD960 IS LCD Screen Replacement

Schwierigkeitsgrad

Moderate

Schritte

21

Zeitaufwand

20 - 30 Minuten

Einleitung

Many camera problems can be fixed by replacing the LCD screen. If your screen is visibly cracked or broken or has been damaged due to impact or exposure to liquids, replacing the LCD screen may resolve your issues.

  1. XInJ5Q16ZEw6ydAW

    • Turn the camera over so that the bottom of the camera is facing up.

  2. FBMDQX1UOMDBdR3o
    FBMDQX1UOMDBdR3o
    aQiPFhpQOnpl1Gst

    • Apply slight pressure to the battery door and slide your finger over the release button in the direction of the arrows to open the battery door.

    • The battery door will open, allowing you to access the battery.

  3. GVBesERRkqouicfY

    • Push the the orange battery lock back to release the battery.

    • Remove the battery.

  4. EU6ARgVr1oCUIhCu

    • Working on your electronic device while it is powered on can result in electric shock. Power off, unplug, and remove the battery of your device before continuing.

    • Close the battery door, and turn the camera over so that the bottom of the camera is facing up.

    • Using a PH000 screwdriver, remove the two 5.5mm screws.

  5. ponj42mFIlKnTRuQ

    • Turn the camera over to the side

    • Remove the two 4mm PH000 screws from the side of the camera.

  6. VpsKGM5SEOEeefFf
    VpsKGM5SEOEeefFf
    6T2OxMQHg1TQQS6K

    • Turn camera over to the data port side with the panel that reads A/V Out.

    • Lift open the latch that covers the camera's data ports.

    • Remove the one 2.4mm PH000 screw on the left.

    • Remove the one 4mm PH000 screw on the right.

    Warning: Before removing (#7) the front cover, three screws must be taken off, 2 on the upper part of the camera, 1 on the left side (when facing the lens). Otherwise, very bad choice….as, on my own camera, the front panel is sticked to a part which isn’t on those pictures. May be Canon has changed the shape of this front panel???

    Philippe ARAKELIAN -

  7. pSPKCjlXt6RnVbyD
    pSPKCjlXt6RnVbyD
    KXmLlEcEgFGNbLFy

    • Turn the camera over so the lens is facing up.

    • Remove the front cover.

  8. Xcw6FCffeldMUffl
    Xcw6FCffeldMUffl
    pZfRdHaQiUWs5AUP

    • Turn the camera over so that the screen is facing up.

    • Remove the back cover.

  9. QEkdDSURbRNgEQVH
    QEkdDSURbRNgEQVH
    yHrDtfpBhP61jB2y

    • Turn the camera over so the lens is facing up.

    • Remove two 2.4mm PH000 screws from the plate on the front of camera.

    • Gently remove the plate.

  10. bCCKgsjY41hJOtjb
    bCCKgsjY41hJOtjb
    OtLjqrKnYQNsP2cO

    • Turn the camera over to the data port side again.

    • After removing the front panel in the previous step, the AV/OUT panel should be free to remove. Gently slide out the A/V panel.

  11. sNSy6q6n3ntIILWW
    sNSy6q6n3ntIILWW
    uXvyTk1qRbUGXKot

    • Turn the camera over so the top panel that reads "Image Stabilizer" is facing up.

    • Remove the two 2.4mm PH000 screws from the top of the camera to the left of the power on/off switch.

    • Gently remove the panel from the side of the camera.

  12. TNRQsPrPfbMEBlJk
    TNRQsPrPfbMEBlJk
    FLASBsgr5XgFPR1t

    • Turn the camera over so the screen is facing up.

    • Remove one 3.2mm PH000 screw from the top of the LCD screen.

    • Remove one 3.2mm PH000 screw from the bottom of the LCD screen.

  13. fhAwCuUdGCqVQYZR
    fhAwCuUdGCqVQYZR
    G5S3e16U4pOgLI1s

    • When you remove the top panel it will remain attached by a small orange cable. You can leave the cable attached; it will not obstruct you from completing the following steps.

    • Gently remove the top panel.

  14. PRTobgOjF1PUpoM3

    • Remove two 3.2mm PH000 screws on the side of the camera, to the right of the button that reads "Func. Set."

  15. xKESXSUpxhSZuowW
    xKESXSUpxhSZuowW
    Ja5IeLOJobyTboMO

    • Use a nylon spudger to flip open the teeth holding the small, orange data cable in place.

    • Gently remove the small, orange data cable. The cable should now hang free.

  16. cOkoiJJHA6NMsYVM

    • Once the data cable is removed, the panel to the right of the LCD screen with the button that reads "Func. Set" will be free to remove.

    • Gently remove the panel to the right of the LCD screen.

  17. NbarT4FFoJFtNSSM
    NbarT4FFoJFtNSSM
    SwWOftBfwXkGiNpB

    • Locate the large, yellow data cable by turning the camera over so the lens is facing up.

    • Find where the data cable connects on the front of the camera.

  18. WOUhWKjlQBGJTObm
    WOUhWKjlQBGJTObm
    nFu4kPPbLHf2YslA

    • Use a nylon spudger to flip open the teeth that are holding the large, yellow data cable in place.

    • Gently remove the data cable.

  19. PdOjvcGk3PZJCGAu
    PdOjvcGk3PZJCGAu
    oUIYKrptJTPHJ1jL
    uELsG1XhAjBUfubW

    • Turn the camera over so the screen is facing up.

    • Remove the LCD screen.

  20. MIFCOInHsCHZSdCL
    MIFCOInHsCHZSdCL
    NNNJqYFIOGpjF3Ok
    ZOHDcb1djDIih3UQ

    • To remove the casing around the LCD screen, begin by removing the top of the casing (which is in two pieces). First, remove the small hinge on the right side.

    • Then, remove the rest of the casing.

    • The top of the LCD screen casing should now be removed.

  21. mKKPQT6OFGZoZI5m
    mKKPQT6OFGZoZI5m
    M3EUCJYgPcAPh2TW
    XY3VqysCmIBowEJY

    • Carefully slide out the LCD screen from the back part of the casing.

    • You should now have three components: The back of the LCD screen casing, the LCD screen, and the front of the LCD screen casing.

    • The LCD screen is now removed and can be replaced or set aside to access other camera components.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Kacy Ewing

Mitglied seit: 16/09/16

253 Reputation

0 Kommentare