Einleitung

The lens is used for capturing specific scenes and to feed these scenes into the camera.

  1. jnG5EusXabWjUUcD
    jnG5EusXabWjUUcD
    iPaEuATZkHq3NONl
    • Slide the grey latch to open the battery compartment.

  2. ILSvsikeGm5VDBDU
    ILSvsikeGm5VDBDU
    LQqCmCa1ZuWNGHWj
    • Push and slide the orange retaining clip to the right to remove the battery.

  3. Ng5LKyIfSSF4ZItG
    • Remove battery from the camera.

  4. FgNfZomEKeWVxAvE
    • Remove the lanyard.

  5. ARCLXwgcvyLsZJg6
    • Position the camera so that the bottom is facing up.

    • Remove the two 2.3mm screws beneath the name plate.

    • Remove the two 2.8 mm screws surrounding the threaded tripod mount.

  6. 55YZVyDXHytDYF4G
    • Remove the 3.8mm screw from the back face of the camera.

  7. DatMem3EBrQJtHAf
    • Remove the two 2.3mm screws from the right face of the camera.

  8. M1hX242rya1yPONK
    • Remove the two outer 3.2mm screws from the left side of the camera

    • Remove the two inner 3.7mm screws from the left side of the camera.

  9. uMAPiWK1SV6QYy6w
    • Pull the back face panel away from the front end of the body. This may take some wiggling and force.

  10. NgZ3DTZsNolIUeMh
    NgZ3DTZsNolIUeMh
    QUoRlh2LBV3gUYxY
    • Remove the CF card door from the left side of the camera body.

  11. ovrKyrxa1FmsQsXT
    ovrKyrxa1FmsQsXT
    GSxAnfOBNIGAyjQv
    • Slide the rubber digital a/v cap out of place on the front plate.

  12. RgoureTMknZwWY3m
    • Remove the front face by sliding it off.

  13. LcUtagAQEgQ4YDQX
    • Remove the rubber seal that covers the right side of the viewfinder.

  14. h2sDExe4TbFX5gI4
    • Remove the two 3.9mm screws that hold the laminated copper sheet.

  15. OgRJQgGnTgnNcB5b
    OgRJQgGnTgnNcB5b
    5x5EmJpDCLDFpnWs
    • Remove the wire connections that connect along the bottom of the motherboard.

  16. Q3t1RqIp53n5ykR5
    • Remove the single 3.8mm screw that is on the motherboard.

  17. WcR5GVmyArHoIETg
    • Remove the motherboard from the main frame of the camera body.

  18. eyGdHXOgYcZyOF1Q
    • After completing the removal of the motherboard, remove the tripod mounting screws (3.4mm) on the left side

  19. klblcEXNurvcGmGA
    • Carefully pry the left side of the housing plate from the bottom of the tripod mounting plate, releasing it from the two alignment pegs next to the screws

  20. aaSchJFjL2YRY1Uo
    • Lift the left side of the tripod mounting plate towards you, lift free the mounting plate from the rest of the assembly

    • Be careful because there are still wire connections attached to the mounting plate which you don't want to remove

  21. jqCMUqLwifGfOTLh
    • Remove the 2.1mm screws from the bottom and top of the screen connecting it to the housing plate

  22. tnbFEUnupCdJCyx2
    • Unsolder the four points at the top of the screen with a soldering iron

    • You do not need to unsolder the screen to get to the lens, but follow the rest of the steps to free the screen from the housing plate.

  23. SUMqbCgWayvnTrOR
    • Remove the card-reader shield by removing the screw at the top of the shield.

  24. KEJD33KkhjQbpqbN
    KEJD33KkhjQbpqbN
    yWBHnWe25BvaNgbN
    • Remove the 2 black screws that attach the battery box to the housing plate.

    • The second picture shows the battery box detached from the housing plate.

  25. M2ouAXtelumwbU3r
    • Remove the three (3.1mm) black screws that were behind the screen and battery box.

  26. wMmUOYPRqMSC6mDC
    wMmUOYPRqMSC6mDC
    CChIJfLRM2N1yA2l
    • Carefully remove the lens.

    • Remove the bottom side of the lens first before the viewfinder side.

    • Be careful of wires and delicate parts.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Joseph Melo

Mitglied seit: 08/04/11

123 Reputation

Ein Kommentar

Camera in the pictures is not Canon Powershot S200

jkovalai -