Casio Exilim EX-Z70 Lens Replacement

Geschrieben von: Paul Fallon
  • Kommentare: 0
Casio Exilim EX-Z70 Lens Replacement

Schwierigkeitsgrad

Moderate

Schritte

15

Zeitaufwand

30 Minuten - 1 Stunde

Einleitung

If your lens have cracked, stopped working, or malfunctioned in any other way, you may need to replace the lens. This guide will isolate the lens so that it can be replaced or investigated.

  1. Go3UTHnqtFg1STn3
    Go3UTHnqtFg1STn3
    VNWqB2EZZPEJYtPL
    QDcTWUcLCw1YGYuc

    • Remove the strap from the camera by pulling the thin cord out, creating a small loop, then pushing the thicker cord back through this loop.

  2. xPUKSRhmCuEfJQ2J
    xPUKSRhmCuEfJQ2J
    sPcVYqoXZUSTYI51
    4mEUiqwGiDMjtGvL

    • Remove the two Phillips screws (2.83 mm) from the left side panel of the camera casing.

    • The left panel can now be removed. However, one piece of tape attaches it to the camera, so a spudger may be required to ease the panels off.

    • Repeat for the right side panel of the camera.

    • Keep track of which screws go where. There are a couple sets of screws to take out and they are all small and look the same.

  3. JfP4r6ewmqCTGyMI
    JfP4r6ewmqCTGyMI
    kTPZCVMeAYG6IRVe
    RnOSaikEkStCqYFt

    • Remove the six Phillips screws (3.69 mm) from the bottom of the camera casing.

  4. GKGE14oSXFVbywvt
    GKGE14oSXFVbywvt
    v5rNVc65C1KgKRrD
    UummG5Gb2J2XBaLF

    • Remove the two Phillips screws (2.79 mm) on the left side of the camera where the metal panel used to be.

    • Repeat for the two Phillips screws (2.79 mm) right side of the camera.

  5. voFj5tPqUmBHXLU6
    voFj5tPqUmBHXLU6
    hkw1X5SlPgZauwdL

    • With the LCD screen facing up towards you, start at the bottom of the camera and gently pull off the back of the casing.

  6. TxYZwqbfIxcZrELf
    TxYZwqbfIxcZrELf
    lwWlmAXfmRR1lMyP
    qBkZQpTGuo2CMc2A

    • With the front side (with the lens) facing up towards you, start at the bottom of the camera and gently pull off the front of the casing.

    • The nob that previously held the camera strap will no longer be attached to the camera once you remove the camera casing. When putting the camera back together, remember to put the nob back into position before replacing the casing.

  7. WXHpHAC3meqfpkQ2
    WXHpHAC3meqfpkQ2
    qlb3HNBtfTIBnUBU

    • Slide the labeled piece toward the LCD screen and release.

    • The tab will spring open.

  8. YBVSmfRNGb1Dy4WU
    YBVSmfRNGb1Dy4WU
    JgPWCedMkiWk2els

    • Look at the bottom of the camera. Take out the Phillips screw (1.77 mm) holding on the bottom plastic piece.

    • The bottom plastic piece is held on to the main frame of the camera only by two thin wires.

  9. BOrAWR5pHXkGaUmS
    BOrAWR5pHXkGaUmS
    AlHfa4Mf6ZZvObKq

    • Use a pair of tweezers to gently move the wire around part of the lens away from it so that you can access the lens.

  10. Qi3vQBVQREKjgPwO
    Qi3vQBVQREKjgPwO
    2fWj1KsI1WJhNVtc

    • The lens is held in place by two metal tabs: one located directly under the circuit board between the flash and the lens and the other located between the lens and the speaker.

    • Using a screwdriver, push the metal tab toward the center of the circuit board.

    • This frees the lens in that corner. However, this step may take some tweaking to properly release the lens.

  11. KFuToBYBmFBPb16u
    KFuToBYBmFBPb16u
    LOjoVoUXskAhCUww

    • As you pull the lens up and out of the casing, push the hook in the lower right hand corner of the lens out of the way.

    • At this point the lens should be connected to the camera solely by two orange plastic strips.

  12. W3sgXJmj2KVLBApe
    W3sgXJmj2KVLBApe
    T11eQDRCVZlMliQW
    OMR6XIZ5leubSJjT

    • Using tweezers or your finger nails, pull up the brown flaps where the two orange film strips connected to the lens meet the circuit board.

    • Use the tweezers to pull the orange film strips out of the port. It should come out easily.

    • There are two additional film strips connected to the circuit board that do not need to be removed. These are connected to the side of the circuit board that is opposite to the lens

  13. 5ZLcPIRDs2pOqEPp

    • You can now remove the lens completely. There should not be anything else holding it in place.

  14. Rg5vYLBfYNr1hRZo
    Rg5vYLBfYNr1hRZo
    yCNJF2icBacnXRAh

    • Turn the lens over

    • On the back are four screws. Remove the two silver phillips screws (4.36 mm) from the back of the lens.

  15. WGZO32DZSqFHaZw3

    • Remove the now loose orange piece from the back of the lens and set it aside.

    • The lens is now ready to cleaned and maintained or replaced with a new one.

    • Since a new lens does not come with the orange film or electronic image sensor, make sure that you keep both the 4 screws and the image sensor and replace them when you install the new lens.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Paul Fallon

Mitglied seit: 10/04/12

138 Reputation

0 Kommentare