Cobra 29 LTD Classic Outer Cover Replacement

Geschrieben von: Chase
  • Kommentare: 2
Cobra 29 LTD Classic Outer Cover Replacement

Schwierigkeitsgrad

Easy

Schritte

11

Zeitaufwand

15 - 20 Minuten

Einleitung

This outer cover is the main cover that protects the inner electrical components. Perform the guide on a flat non-conductive surface to avoid electrical shock and damage to your device.

  1. ePvXXqIskEeDt3rE
    ePvXXqIskEeDt3rE
    wuRcDdttwaNHEL4g

    • Turn the power switch, the leftmost knob, counterclockwise to off.

  2. MHaoPyusxO1fdHUM
    MHaoPyusxO1fdHUM
    PLAWU6BBUOJJmhdN

    • Turn the device around and firmly pull the power cable plug to remove it from the radio.

  3. Rsn2uDHEhUtmHkln
    Rsn2uDHEhUtmHkln
    JMnkVOonFSrMAb6l

    • Unscrew the securing cap counterclockwise from the antenna connector.

  4. xCMkIZv3kItGLEIj
    xCMkIZv3kItGLEIj
    eThimSUNgTCN3jmT

    • Gently pull the antenna cable to remove it from the back of the radio.

  5. TbH6kKQA3BroPpVy
    TbH6kKQA3BroPpVy
    HwqDymUIUSdhDRwb

    • Unscrew the cap counterclockwise on the microphone plug to disconnect the cable.

    My mike will.not key

    Keith Laws -

    My microphone will not recieve or get out

    Keith Laws -

  6. uvDgaS4RJVJc1q4r

    • Gently unplug the microphone plug.

  7. 1QqXCYEtwBq11JEs
    1QqXCYEtwBq11JEs
    im6UkjSF66Z5BW5n

    • Unscrew the top four 6.0mm Phillips head screws counterclockwise on the left and right side of the device using a #1 Phillips head screwdriver.

  8. bEmV2uVGSqnuurUP
    bEmV2uVGSqnuurUP
    hQhavRwWx3BUYcyv
    Ab4SWKuCXjOoljyb

    • Gently life and remove the top cover.

  9. NYhaMtYtjiUSwFKM
    NYhaMtYtjiUSwFKM
    5OCAxwRhpnNR2Wgr
    fOaF1GqUuLdZIqqF

    • Gently set down on a hard, flat, non-conductive surface to minimize risk of shock or breaking your radio.

    • Carefully flip the radio over.

  10. WShpKPZ1CRywkmxO
    WShpKPZ1CRywkmxO
    h3oUWcBPkRCuGMpa

    • Unscrew the four 6.0mm Phillips head screws counterclockwise on the left and right side of the device that connect the remaining cover, using a #1 Phillips head screwdriver.

  11. ypKnXmBmKSavRBUP
    ypKnXmBmKSavRBUP
    SUYDw4PfMNtKRP2T
    mYutrwNXQ2aXquyY

    • Watch out for the wires connected to the speaker. These short wires will not allow you to move the cover very far.

    • Gently lift and remove the case cover.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Chase

Mitglied seit: 20/10/13

267 Reputation

0 Kommentare