DBPOWER T20 Disassembly

Geschrieben von: Andrea Espinosa
  • Kommentare: 5
DBPOWER T20 Disassembly

Schwierigkeitsgrad

Moderate

Schritte

10

Zeitaufwand

15 Minuten

Einleitung

If you need to repair anything on the DBPOWER T20 Projector you need to disassemble it first. This guide will show you all the steps necessary to disassemble the device to a point where items can be replaced. It is quite a sturdy device so don't be afraid to use some force removing the top of the device and the wired. However, use caution around the mirrors inside the device.

  1. EWsMPA6kyq5dmO4b

    • Flip the device and lay flat.

  2. tbGKi5YOBUPMMkUO

    • Remove the four (9 mm) screws with a PH2 screwdriver.

    • Remove the two (7 mm) located with a PH2 screwdriver.

  3. 4VJodpDJZlvPRqFD
    4VJodpDJZlvPRqFD
    ZSSUp2hSamESYMSV
    XjdUujnaf5LZB4n6

    • Flip the device over and pry the top off with a plastic opening tool.

  4. EXWaF2ou5NcX1lYF

    • Remove the ribbon cable connecting the motherboard to the button control board by gently pulling it from its connector.

  5. fWYsIxUnQjGA2Kyx
    fWYsIxUnQjGA2Kyx
    j4LHonCJvPoNTF1O

    • Remove four (6 mm) screws connecting the motherboard using a J0 screwdriver.

    one of the screws have been stripped, I’ve tried the rubber band and the glue trick, it didn’t work. What do I do to remove it? please respond

    arman waggoner -

  6. trRAUNLES2IFlrKD
    trRAUNLES2IFlrKD
    vQkSSglA43265rNO
    OcQnJ5HSa6hoNBOA

    • Remove the two cables connected to the motherboard: black power cable and the red/black fan cable.

    • the black cable requires more force to remove than the other cables.

  7. joEhEZpGBaYLpUcM
    joEhEZpGBaYLpUcM
    BOHRrUVkxpouFQeU

    • Lift the black latch on the ZIF connector and remove the ribbon cable that attaches the digitizer to the motherboard.

  8. PI4iXGIZQqnlLOHb

    • Raise motherboard by lifting sideways and then up to avoid the ports.

  9. SZxjwAKmBROTtIES
    SZxjwAKmBROTtIES
    m24f1a2qX3U2OCYs

    • Remove wires attaching the piezoelectric speakers to the motherboard.

  10. PIuyVcthnU1aInaI
    PIuyVcthnU1aInaI
    JottcDMKwepGPKZh

    • Remove the five screws securing the black plastic cover with a J0 screwdriver.

    • Lift up and out to remove.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Andrea Espinosa

Mitglied seit: 15/02/18

506 Reputation

4 Kommentare

Anyone find a bulb for this thing? And/or know what else (or a quick fix) would fix a dark or burn mark on the image?

jcr4130 -

haing the same issue tried to call a electronics repair place to see if the could order a new polarizing lens for me and they said they could not unless they were the ones that did the repair

derek_russell82308 -

Really? Well, crap

KweenBeeTX -

How are the lenses supposed to sit in the hompow t20 mini projector

Joseph Duffey -