Dell Inspiron 1526 Screen Replacement

Geschrieben von: Ahmed Alshamsi
  • Kommentare: 2
Dell Inspiron 1526 Screen Replacement

Schwierigkeitsgrad

Difficult

Schritte

12

Zeitaufwand

45 Minuten

Einleitung

The screen is an essential piece of hardware that, due to its delicate and large profile, is often damaged. In this guide, we will show you how to replace the screen on the Dell Inspiron 1526 Laptop.

  1. 6vUTlZ26N2DvsFrC
    6vUTlZ26N2DvsFrC
    DTSeQEJBjK4OAOAq
    p1FRqmYhnnQ1p1Ai

    • Slide the unlock button to the left to release the battery.

    • Slide the battery away from the laptop to remove.

    • The unlock button is located on the bottom of the laptop.

  2. AQVhRtk3U3UtMkMs

    • Loosen the two 3.5mm Phillips #1 screws in the battery bay.

  3. mURERATMTmpsGCBy

    • Flip the laptop over.

    • Lift the control cover by prying the right side of the cover with an iFixit opening tool.

    1. Define “plastic scribe”.

    Please also note we are unable to see the tool utilized completely.

    Sean Lucas -

  4. NS4TXHSce3jQIP1R

    • Carefully lift the control cover up and forward to reveal a single ribbon cable.

  5. tV5yyBWPRKdJVGPt

    • Use tweezers to squeeze the tabs on the connector and remove the ribbon cable.

    1. Capitalize the “i” in identify.

    2. Grammer: “Identify the black cable ribbon tab; carefuy pull back from both sides.“

    3. Use the caution bullet for the instruction of “Do not pull hard”

    4. Consider utilizing a tool, i.g. Nylon-Tip Reverse Tweezers, for this step.

    Sean Lucas -

  6. RlbtMRqbMpikvYbc
    RlbtMRqbMpikvYbc
    KSmQu3XhuVSdsmus

    • Remove the control cover.

  7. sbWFNUNYYtfq1WRW

    • Remove the two 3mm Phillips #1 screws at the top of the keyboard where the control cover was.

  8. B2SUa5WuIMC2lBlG

    • Lift the keyboard gently from the top, but do not remove completely.

    • Looking under the keyboard, towards the touch-pad in the center, lift up the black tab on the connector with tweezers for the keyboard ribbon cable.

  9. tXFCXsWBZfYsMJmc
    tXFCXsWBZfYsMJmc
    lfPBTeDPiaqYpUEI

    • Remove the keyboard.

  10. 2m6O1AqtdsqLArdQ
    2m6O1AqtdsqLArdQ
    iaRZ4qmbmXyroPGS

    • Remove the six plastic pads around the bezel using an iFixit opening pick.

    • Remove the six 3mm Phillips #0 screws under each pad.

  11. im1ZXL3tuEL2LOgW
    im1ZXL3tuEL2LOgW
    LXBVGVOylB2nmMDb
    kmvmQBcD4CLJmgQI

    • Open the computer so that it rests flat on the table.

    • Separate the bezel from the black plastic frame using a spudger.

    • There are a dozen snaps around the perimeter of the bezel and there are two between the pivot joints of the laptop.

  12. UWpEpAMgAOEJiwDr
    UWpEpAMgAOEJiwDr
    Pg5sKwY5SNPYUXGm

    • Remove the two 3mm Phillips #1 screws at the bottom of the display panel.

    • Lift the display slightly from the top, then pull outwards.

    • Flip the display panel around to the back.

    • Disconnect the connector and remove the ribbon cable.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Ahmed Alshamsi

Mitglied seit: 17/09/19

181 Reputation

0 Kommentare