Einleitung

This guide demonstrates how to replace the heat sink on the Dell Inspiron 1721 laptop (Model PP22X). Heat sinks prevent overheating on processors that need additional cooling to run at optimal speeds.

The CPU stays cool by “dumping” heat from its surface to the heat sink after which the heat is dispersed into the air. Heat sinks are often assisted by a fan which pulls cooler air across the surface and away from the heat sink. The heat sink can then pull more heat from the CPU, which cools the CPU. It's this continuous cycle of heat transference that keeps the CPU cool.

There are several indicators that your heat sink may have failed. First, if your laptop is running incredibly slow, this may indicate that your processor is self-throttling to prevent overheating. Second, if the laptop’s fan is running at an extreme speed, this could indicate that the heat sink is unable to adequately pull heat from the CPU.

To verify that the heat sink has failed, you will need to conduct a visual inspection to determine if the heat sink is physically damaged. This guide provides the steps to access and, if necessary, replace the heat sink. To prevent shocking yourself or shorting out the motherboard, you must first remove the battery from the laptop.


  1. LnX1GGcU3PUIKxnK
    LnX1GGcU3PUIKxnK
    OMwMTIre6GJgSyAO
    • Slide tabs outward to undo the locks.

    • Grab and pull the battery away from the device to remove.

  2. YImPJKaDer3elWHn
    YImPJKaDer3elWHn
    k6qQhbPT4HFaGGrt
    Q5DfWbI3JeXwgEU3
    • Pry up on the corner of the hinge cover with an iFixit opening tool.

    • Use the iFixit opening tool along both sides and the front of the hinge cover to release it.

    • Lean the display back as far as it goes and lift up on the hinge cover to remove.

  3. 1FpCPvoNKDJcYY2K
    1FpCPvoNKDJcYY2K
    TYxSQHLaaWW4qEFM
    • Loosen the two captive Phillips #0 screws.

    • Remove the cover.

  4. nJcePRyOrFVUsRv1
    • Disconnect the antenna connectors from the WLAN card.

  5. BP3jBLsPPdJQOkVJ
    BP3jBLsPPdJQOkVJ
    IgcsH31VUKbUYBNB
    TDVBwvSwuqp2RALi
    • Remove the 3mm Phillips #0 screw securing the connector to the case ground.

    • Disconnect the display connector.

    • Disconnect the second connector, then remove the cable from the base.

  6. fFJqhPCumtP1b1A3
    fFJqhPCumtP1b1A3
    tv6peRBTVgn5Yk5r
    DkBmnbGmJMbbNJpZ
    • Remove the display cable from the palm rest.

    • Use a spudger to carefully pull the antenna wires through to front of the device.

  7. rRnqYDcLJHimAVtH
    rRnqYDcLJHimAVtH
    HwAw4eOKxkLFSL2K
    • Remove the two 3.5 mm Phillips screws that hold the display assembly in place.

    • Lift the assembly straight up to separate it from the body of the device.

  8. jqLMH2iVtBLn1XlG
    • Disconnect the touch pad connector.

  9. U4a1bxPnbDwtf3Sd
    U4a1bxPnbDwtf3Sd
    GDW3MhhunwtEhFXW
    oCLhUXURAJ3RNPeL
    • Lay the device flat and remove the 17 7mm Phillips #0 screws.

    • Use an iFixit opening tool to separate the back cover.

    • Remove the back cover.

  10. QZMtXXNegwZJLgIV
    QZMtXXNegwZJLgIV
    W3rOkXHt4REXoeSL
    DCxjBqXgTk3TwDQA
    • Unscrew the Phillips #0 screws attaching the heat sink to the motherboard.

    • The screws attaching the heat sink to the motherboard are part of the heat sink.

    • Carefully remove the heat sink from the motherboard.

    • You may have to apply upward force while removing the heat sink from the motherboard, due to the thermal paste between it and the CPU.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Kristen Gismondi

Mitglied seit: 12/11/14

71827 Reputation

0 Kommentare