Dell Vostro 3450 Palm Rest Replacement

Geschrieben von: Johnathan Hammond
  • Kommentare: 4
Dell Vostro 3450 Palm Rest Replacement

Schwierigkeitsgrad

Moderate

Schritte

20

Zeitaufwand

20 - 40 Minuten

Einleitung

In this guide, we will be showing you how to remove and replace the Palm Rest.

  1. xeVwMBRGRTSgfDTj

    • Slide the left and the right battery release latches to the unlock position.

  2. R31yTQ3UOL3J6kKj

    • Slide the battery and remove it from the computer.

  3. D4GTMY1jWY1YojlX

    • Loosen the screw that secures the memory door.

  4. dn2EirSMEWHXeSvC

    • Pry up the memory door near the screw hole, lift and remove it.

    • If this is all you are doing Follow Step In Reverse if not Go to Next Step.

  5. QM46yVHjVFdKZiG3

    • Remove the screw that secures the optical drive to the computer.

  6. DsWOQj5esOdiuXIP

    • Gently pry the optical drive out of the computer.

    Make sure you have loosen the screw beside the keyboard cable latch, mentioned in the comments of Step 8.

    fernandolordao -

  7. iASJ4KO2D3IIYpXM

    • Remove the screws that secure the optical drive bracket.

    You can skip this step when replacing the HDD, it isn’t necessary at all.

    BorpoIT -

  8. GITfUCPN1bVySYQh

    • Remove the optical drive bracket from the optical drive module.

    You can skip this step when replacing the HDD, it isn’t necessary at all.

    BorpoIT -

  9. Hpktn5KJ5mPQdSgR

    • Remove the screws in the battery compartment.

  10. pqLaY2AempXliikK

    • Remove the screws in the optical drive compartment.

  11. HDROuAXxAqFuTKYT

    • Remove the rubber from the bottom base on the right side.

  12. oYHnS4KQdIZfjsuW

    • Remove the rubber from the bottom base on the left side.

  13. 3EQorLXOLolVlDMR

    • Remove all the screws from the bottom base.

  14. 5yBHoCjNswhSHHGQ

    • Flip the computer around and remove the screws that secures the palm rest.

  15. j215aMQlLbrTFsVB

    • Release the latches on the system board connector, then disconnect the touch pad cable and the finger printer cable.

  16. ENBi1mQfGgEGJR6B

    • Release the latch on the system board connector and then disconnect the power button cable.

  17. KE1IMf3vFfaoY4a2

    • Release the latch on the system board connector and then disconnect the hot key cable.

  18. b2uP61kSKLIVoJpW

    • Pry up the right side of the palm rest.

    There are a couple of latches on the front of the palm rest which should be released before you move on to the sides. I think one of those latches is released in the picture above. The iFixit opening tool was helpful here, and I used some of the iFixit opening picks to stop the corner latches from closing while I worked on others.

    BorpoIT -

  19. NCT3YWHdLiGhqlfV

    • Pry up the left side of the palm rest.

  20. JLyf4OlnR5ql1HRW

    • Pry up the sides of the palm rest and remove it from the computer.

    • If this is all you are doing Follow Step In Reverse if not Go to Next Step.

Tinte & Feder

Johnathan Hammond

Mitglied seit: 28/02/18

44352 Reputation

0 Kommentare