Einleitung

  1. XnaKobXZhTP2uhKv
    • Press the battery release tab and the battery will pop up.

  2. mFfrlySBpBmKRUfX
    • Remove the battery from the laptop, it will come out easily.

  3. eWgyA6JxEWbReXu6
    eWgyA6JxEWbReXu6
    OdkSRIJVSZ1Jrd5P
    • Remove the single screw holding the accessory plate. This is a PH0 2.0x2.5 screw.

  4. UthonsRSXpVxGeLq
    UthonsRSXpVxGeLq
    eZDUKjfmqJgka4HW
    IiS23lEg5tTYtWnT
    • Pry the accessory plate up from the back of the laptop by applying force upwards where the screw was removed.

  5. epcGFbgx3MBFNpTH
    epcGFbgx3MBFNpTH
    RrsWYaLpByEIpDxr
    • Remove the PM 2.0x2.5 screw with the PH#0 Screwdriver attachment that is shown at the corner of the Solid State Drive.

    • After you have removed the screw, the Solid State Drive should lift up.

  6. CeZIUFLlSgZxNShj
    CeZIUFLlSgZxNShj
    QriM4eWwZDFcNyXX
    • Very carefully, remove the SSD by gently pulling away from the SSD socket.

  7. 15R5iOAj1mQZsEKB
    15R5iOAj1mQZsEKB
    gLTyriFKSSUenNQb
    • Use the plastic opening tool to pry the hard drive away from the board. Notice that there is a slit centered at the back of where the hard drive is sitting. This is where you'll insert the plastic opening tool as shown in the photo. Finally, pry with the plastic opening tool to remove the hard drive.

  8. uLpt1T4OL1Pcs3gW
    uLpt1T4OL1Pcs3gW
    uWZmSkiHUTw4vV21
    • Firmly grasp the connector's base as shown and pull to remove from the hard drive.

  9. ORgCX2NZOLBmSCqB
    ORgCX2NZOLBmSCqB
    rKJLRWoR1QNE3Pcu
    5LiekU5FtMxBVDYW
    • Remove the highlighted rubber stoppers with a metal spudger as pictured. They should expose a screw that you will need to remove in a later step.

  10. 5Drc6Y1RTbAAOfbr
    5Drc6Y1RTbAAOfbr
    PJvkFq5VVEAvvRSn
    RXdeT2bfURY1uM4c
    • Remove plastic cover highlighted. It should expose a screw that you will need in a later step.

  11. pZ2AwqO6YkXc6iNT
    • Remove all highlighted screws with PH 1 screwdriver. These screws are PM 2.0x2.5.

  12. vEs1XpTQtx6HLDmV
    vEs1XpTQtx6HLDmV
    XAM3qwQDg2igXSRy
    • Remove all highlighted screws from the battery access area. These are PM 1.5x2.0 screws

    These were very tricky for me, I ended up with one nonfunctional screw, it seemed as if the 00 was a bit too large for the screw.

    Yonatan Abrego -

    Use the PH0 bit for this step.

    kevinbush85 -

  13. QiGRomEMXAfDSZk4
    • Remove screws highlighted with PH1 screwdriver from accessory plate area.These are PM 2.5x3.0 screws

    • Remove screws highlighted with PH1 screwdriver from accessory plate area. These are PM 2.5x4.5 screws

  14. AYu6iLener2KAajO
    AYu6iLener2KAajO
    FGwjZ3wIqvXwT5Cj
    iNGDK41VWTjZZsGT
    • Pry open back plate area with plastic opening tool. The back plate should pry open with relative ease. If you feel some resistance at any point please refer to steps 2-5 because a screw has probably been missed.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Ramon Villadonga

Mitglied seit: 04/09/15

1011 Reputation

0 Kommentare