Disassembling IBM ThinkPad A30 CPU

Geschrieben von: Jessica
  • Kommentare: 0
Disassembling IBM ThinkPad A30 CPU

Schwierigkeitsgrad

Moderate

Schritte

18

Zeitaufwand

Keine Schätzung

Einleitung

  1. LojZOTKUVLIFLI2V
    LojZOTKUVLIFLI2V
    KFTIp3x1sSkAhvjA

    • Flip the ThinkPad over so that it is upside down.

    • Slide the highlighted tab to the left.

    • With your finger on the tab, remove the battery by lifting it upwards away from the laptop.

  2. lZxRAtGd2x6mkF6p
    lZxRAtGd2x6mkF6p
    PSn2r1SBx5wSQkiW
    4mImMjaIMQdhBdXY

    • Remove the highlighted screw with a Phillips #1 screwdriver.

    • Pull the hard drive out.

  3. YOHHnmoUkp6IKeAD

    • Make sure the laptop is upside down and oriented in the direction shown.

    • Remove the six 16.7mm screws inside the circled holes.

  4. qliMGVEk1rnii4pJ

    • Rotate the ThinkPad so that the hard drive bay is facing you.

    • Remove the black cover to reveal a 14.8mm screw.

    • Remove the uncovered screw with a Phillips #0 screwdriver.

  5. awqZ6OGMIVsXTpMb
    awqZ6OGMIVsXTpMb
    1236sEeEkudw3oEe

    • Flip the ThinkPad over and open the LCD panel.

    • Pry apart the keyboard with a plastic opening tool or with your fingers.

  6. hUMMD54OTLkMWaSi
    hUMMD54OTLkMWaSi
    SCNi2HOLe35w2NaV
    WROPmyH6dVkwiNYs

    • Be careful not to pull out the keyboard carelessly; there is a connector underneath it!

    • Lift the front end of the keyboard as shown.

    • Using your fingers, remove the black film cover.

  7. JNGGRLeT4B5NOSvE
    JNGGRLeT4B5NOSvE
    QDRX4UdkIxskLUcq
    BNmkH25bWPQAFhYb

    • Locate the connector attached to the motherboard.

    • Disconnect the ribbon cable by removing the connector.

  8. yH3neYDbx3FGEOvr
    yH3neYDbx3FGEOvr
    o1KTFP6BQJMk1VKL

    • Lift and remove the keyboard.

    • Remove the two 5.6mm screws.

    • Remove the 16.7mm screw.

  9. i3uvoJibxsyAXLQv
    i3uvoJibxsyAXLQv
    fCqxglA1KGNANkJX
    LWTgV5OwEshOiZMk

    • You will need to use a little force. Be wary of the tabs.

    • Pry off the upper case with your hands.

  10. Rvnw2xiXDZGMSXXL

    • Remove the 5.6mm screw that holds the LCD to the upper case.

  11. FMFULPfdXbOIK5Qg
    FMFULPfdXbOIK5Qg
    Y5HJpKREZDHLILRf
    RUIHuj2mdkF1ixRo

    • Remove the 5.6mm screw on the left side of the three-pronged connector.

    • Remove the other two 16.7mm screws.

    • Lift and remove connector.

  12. ZWYKKdCxr1pOvEN1
    ZWYKKdCxr1pOvEN1
    iTbIcOsJUZnuyPj4

    • Pull out the white tab connecting the LCD to the motherboard.

  13. rm25WRrrSQ1VNjNi
    rm25WRrrSQ1VNjNi
    pCfenvkHOX1ZSCPC

    • Turn the laptop so that the back is facing you.

    • Remove the four 5.6mm long screws.

  14. qtdUNKD6OctdSRmx
    qtdUNKD6OctdSRmx
    JxDXRHsKa2Pb5oca
    lLRj1fPdf1hqqUKF

    • Place the laptop so that the LCD is facing you again.

    • Gently lift the LCD monitor up and out.

    • Remove the black plastic tab.

  15. ZaYH3TMhFpHIjmXX

    • Locate the 4 screws that will need to be removed.

    • One screw (yellow) is noticeable. The three other screws (red) are below the heatsink bracket.

    • Remove the 5.6mm (yellow) and three 16.1mm (red) screws.

  16. KpFkTrPmvUNvnJoU

    • Lift the heatsink bracket up.

  17. hdTUuXEcxBGJPuvp
    hdTUuXEcxBGJPuvp
    uUDCOCREnaQgEufT
    VlBShwfTTq2pR2XE

    • Be careful not to pull too hard! There is a cable attached to the fan!

    • Lift the fan/heatsink assembly up.

    • Locate the fan power cable and pull upwards near the connector.

    • Remove the fan/heatsink assembly.

  18. ZTHIwPJagw2lycCo
    ZTHIwPJagw2lycCo
    sqP2kXqtB3mDgFLh

    • Use a flathead to turn the screw 180 degrees.

    • Remove the CPU by lifting it upwards.

    • If the CPU is reusable, place it in an antistatic bag and away from moisture.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Jessica

Mitglied seit: 06/10/10

162 Reputation

0 Kommentare