Dremel 4000 Power Cord Replacement

Geschrieben von: John Cobb

Kommentare: 11

Schwierigkeitsgrad

Moderate

Schritte

Zeitaufwand

7 Minuten

Einleitung

In the following steps you will access the electrical assembly, and remove the positive and negative wires that connect the power cord to the assembly.

Werkzeuge

Schritt 1

Start by removing the housing cap by unscrewing it.
Next, unscrew the now exposed collet nut while holding down the shaft lock button.
To remove the collet nut, you may need to use the small open-end wrench provided with the Dremel.

Is this a joke??? Wanna maybe possibly tell US WHAT A COLLET NUT LOOKS LIKE?? I mean it's obviously very exposed (not exposed one bit. My Dremel 4000 looks exactly like it did before. No Collet nut suddenly stood out) and not all of us have advanced degrees in Dremel parts

Jeff Wagner -

Dam Jeff. I am not sure if you are being sarcastic or not, but maybe you should go lie down for while.

itguyfla -

Schritt 2

Using your hands, carefully remove hanger from casing.

Mine seems to have solid caps without the slot. How are this type removed?

claire roche - 19/10/20

This is getting worse. Maybe skipping the Collet Nut part threw me off - as there is no hanger. This description is PATHETIC!!!

Jeff Wagner -

I love how these pictures show you NOTHING related to what this guy is talking about

Jeff Wagner -

Wow, you guys are really amazing. Are you actually working on a Dremel 4000? Mine looks exactly like the pics. It has a hangar on it, as well as a collet nut.

itguyfla -

Schritt 3

Remove the brush caps (one on each side) by using a flathead screwdriver bit.
The brush caps are spring loaded.

I have found that the brushes are the most likely failure point on the Dremel tool. I haven’t purchased a new one in many years but they used to come with a spare set.

In general commutator brushes are made of a soft high carbon compound, usually found with new springs attached. The brushes can be carefully reshaped using files, sandpaper and a razor knife to fit the recesses of the tool.

Use the original to get necessary dimensions, a dial caliper is very helpful here to duplicate channels and recesses as well as determining how long the brushes should be. Should you need to shorten the brush a new concave can be established using a pencil or dowel wrapped in sandpaper being sure to match the concave to the channels so it matches the armature. It is preferable the curve be wider than the armature so edges don’t catch, it will naturally wear into a perfect curve. Blow off before installing.

Once the tool is reassembled turn on and off several times then run for a while varying the speed.

George McNew - 27/07/22

Schritt 4

Using the Torx 15 screwdriver tip, remove the 5 screws (12.5 mm) that hold the casing together.

Schritt 5

Use a plastic opening tool to gently wedge apart the hard plastic threads.

Schritt 6

Use your hands to carefully remove the back casing so that none of the components fall out.

Schritt 7

To clear access to the electrical assembly, remove the variable speed dial cap and blue power lever, and set them aside.

Schritt 8

Using your fingers, carefully pull the circuit board from the casing. This will make it easier to remove the power cord.

Schritt 9

Each wire is fed through a small opening on the circuit board and held with a flat head screw.
Loosen the screw just enough to remove the wire by gently pulling it with your hand.

Hello I need to know or see where is plugged the blue wire, I think that know the problem it is disconnected? Thank you. if you need my e mail. charbonneau_eric66@hotmail.com

charbonneau_eric66 - 18/01/17

on t11 and t12, which one is positive and which one is negative?

Marc Webb -

Hey Marc, the leads that go to T11 and T12 are mains (AC) current. The black wire goes to T12, and white to T11.

itguyfla -