Epson Stylus Photo 1400 Housing Replacement

Geschrieben von: Larry Huang
  • Kommentare: 3
Epson Stylus Photo 1400 Housing Replacement

Schwierigkeitsgrad

Easy

Schritte

12

Zeitaufwand

15 - 30 Minuten

Einleitung

To get to the inside parts of the printer, the housing components must come off.

  1. lccTL6SZ3kbvrUG2

    • Turn off the printer.

    • Disconnect all data connections coming into the printer such as USB, networkd cables, firewire, etc. as well as removing the power cord.

  2. QYteIeiAr3eYANHf
    QYteIeiAr3eYANHf
    YacUSN6hThuTEpFy

    • Locate the IEEE cover in the back.

    • Gently slide the cover to the right to unlatch, then pull to remove it.

    errore avevo chiesto informazioni x sostituire la batteria al cellulare HUAWEI Mod. LX1

    Luigi Martinenghi -

    avevo chiesto informazioni x la sostituzione della batteria cellulare HUAWEI Mod.LX1

    Luigi Martinenghi -

  3. C4dBWDDOARfU6BKl
    C4dBWDDOARfU6BKl
    Zobe3GQ4ytZXQuXj

    • Using a Phillips #2 screwdriver, remove the four 10 mm screws shown.

    • Remove the 6 mm screw that holds the rear housing in place.

  4. iSFOcWcCsIxvdqON
    iSFOcWcCsIxvdqON
    BfSTmc334IPJEjIW

    • Remove the rear housing by pulling it backwards.

  5. ZRQjtn2Y1AjXrlTx
    ZRQjtn2Y1AjXrlTx
    VS6Om6BsNLdA6RX1
    q1rUDpQs4M13aSXO

    • Insert a plastic opening tool into the cutouts of the lower housing.

    • Release the two tabs of the side housing by lifting the tool in an upward motion.

    • Remove the side housing by pulling it outwards.

  6. vfiVSPXdkGxi1FFa
    vfiVSPXdkGxi1FFa
    fEIKc1TbHiBORjdF

    • Both side housings are attached by the same type of mechanism.

    • Using the same method, remove the other side housing.

  7. JyXjekvUHEsuITOZ
    JyXjekvUHEsuITOZ
    GHYP2VbWwuIIexap
    Twc3ylCxi3RZdNAd

    • Lift the paper support.

    • Open the printer cover and front cover.

  8. XgpHaunnOSVioafK
    XgpHaunnOSVioafK
    xxXUiIkZyPRmwsnn
    uD12N4KNMu1DRYHI

    • Remove the four 10 mm Phillips #2 screws from the sides of the printer.

    • Remove the three 6 mm Phillips #2 screws.

  9. iTMoHjNDg4EXjWr6
    iTMoHjNDg4EXjWr6
    auVkiwhoUQ5t3yOR

    • Detach the tabs from the pins on each side by pulling it outwards.

  10. tCKNoqZRVGbrTnYR
    tCKNoqZRVGbrTnYR
    5CcLsgUa3gDWxdMl

    • Remove the two 10 mm Phillips #2 screws on the front of the printer.

  11. ShQrsIGl1fSNefvJ
    ShQrsIGl1fSNefvJ
    2IXjV2g466oM1Ryu
    RTWbClacrIBJ6yJD

    • Disconnect the two cables on the side by carefully pulling it outwards.

    • You may need to gently rock the two cables up and down while pulling.

  12. GNbFiqQLlN4SnJv5
    GNbFiqQLlN4SnJv5
    4NKVJbuNDxa5hqHg

    • Remove the upper housing by lifting it upwards.

    • It's easier to lift the housing by gripping it from the bottom.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Larry Huang

Mitglied seit: 12/10/11

953 Reputation

Ein Kommentar

Thank you so much, Larry! I am repurposing my 1400 for sublimation printing and need to get the print head a little easier than standard methods! Much appreciated!

ryan Caputo -