Einleitung

This guide walks you through the replacement of the Eureka SuctionSeal 2.0 Pet Brush Roll Belt. A damaged brush roll is a common occurrence and can create several problems, making this a useful troubleshooting guide.

Werkzeuge

  1. tGO3aXEYGEkHcGDW
    tGO3aXEYGEkHcGDW
    AvQGgWkWGiBXGcfs
    • Place the device upright with the brush roller closest to you.

    • Pull up on the latch at the top of the dust cup.

    • Tilt the top of the dust cup forward and pull towards yourself, removing the container from the device.

  2. o4kaihoJ6UqGCgOb
    o4kaihoJ6UqGCgOb
    w3rjI36N2Nc3KIOM
    • Locate the gray exhaust filter cover at the top of the vacuum's base.

    • Grip the two tabs in the middle of the filter cover and rotate counter-clockwise.

    • Lift the cover away from the vacuum.

  3. gqEeRuDiXR5UyJ5Q
    gqEeRuDiXR5UyJ5Q
    WY3gEwvsJXFoaPkH
    EKQwu6SUv4CtlkDe
    • Pull up and unhook the two front tower latches using two fingers. These are located at the base of the tower.

    • Pull up and unhook the latch on the back of the tower.

    • Firmly lift the vacuum tower up and out of its stand.

    • The exhaust filter cover can be replaced once the tower is removed. It will not affect the steps.

    There is a screw on the back located left of the tab. What type of tool can take this out? It’s not a normal screw.

    meshaun9 -

    Actually there is no need to take off the top. I just completed steps 4-10 and It worked! :)

    meshaun9 -

  4. ZP6WVlWTByAPtEBG
    ZP6WVlWTByAPtEBG
    ODOVAeXQXr1xqheA
    • Remove the four 20mm screws on the top of the vacuum head's cover using a JIS 1 screwdriver.

  5. ZoyUip4wYARoejDs
    ZoyUip4wYARoejDs
    vVYW5PU5N4YUXKCq
    • Turn the vacuum head so that the back is facing you.

    • Press the handle release pedal.

    • Rotate the top of the motor cover down while pressing on the pedal release.

    • The motor cover should rotate from an upright position back towards the ground, as it would if the handle were still attached.

  6. 4jtuBbeMNI5fGjHT
    4jtuBbeMNI5fGjHT
    auBkp3KUxVAeFpZW
    mVMFfU3Kh4IbZJMx
    • Locate the two tabs on the back of the cover.

    • Pull up on the tabs and lift the cover away from the device.

  7. IeRALcE4dVlmFUw3
    IeRALcE4dVlmFUw3
    L3KOjULdJtqvQNYf
    • Locate the belt latch assembly. It will be on your right when the brush roll is facing you.

    • Remove the two 20mm screws using a JIS 1 screwdriver.

  8. BflxeyJaSmWhWIwW
    • Lift up on the belt latch assembly and remove it from the vacuum.

  9. PeVvVpqi1YXl46vH
    PeVvVpqi1YXl46vH
    ZoU1SuMyA5MM5WQd
    2IrCbKcANWwAfClg
    • Grab the brush roll on both ends.

    • Lift up on the right side of the brush roll.

    • Lift up on the left side of the brush roll, completely removing it from its frame.

    • Separate the brush roll from the belt and remove the brush roll from the vacuum.

  10. XEOT2j3aBjcKgwMF
    XEOT2j3aBjcKgwMF
    4uAoMAkFSOqJQrg1
    dIJNUnjiv6vpcnoY
    • Rotate the belt until the front is above the motor shaft.

    • Twist the belt away from you, allowing the narrow side of the belt to slip between the motor shaft and the vertical rod.

    • Separate the belt from the motor shaft.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Grayson Clendenon

Mitglied seit: 02/10/17

571 Reputation

Ein Kommentar

Thank you so much for this guide! I actually just needed to complete steps 4-10 for the vaccum and everything worked. No need to take the upper half off any more and turns out I didn’t have to replace the belt. I believe there was just a bunch of thick cat hair caught in between the latch assembly and the brush. Thanks again for your time and effort in putting together this guide!

meshaun9 -