Grace Digital Mondo Motherboard Replacement

Geschrieben von: Nathaniel Brabham
  • Kommentare: 4
Grace Digital Mondo Motherboard Replacement

Schwierigkeitsgrad

Moderate

Schritte

7

Zeitaufwand

20 - 30 Minuten

Einleitung

The replacement for your device's motherboard requires a little extra effort than the other components in the device, but is still easily manageable with a soldering kit. With the little amount of desoldering required for this project, a YouTube video undergoing basic safety precautions and soldering kit use is recommended.

  1. KnSxURNBwqpATH1M

    • Remove (2) screws (14 mm) with a PH1 screwdriver on the device.

    • There is one screw on the back left, and another just below it on the bottom of the device.

  2. jJTKtCDmQJSGjK5y
    jJTKtCDmQJSGjK5y
    pTTPHNakxZPm3bCX

    • Use a plastic spudger to remove the front preset selection buttons.

    • We recommend you remove all of them for easier access.

    • Gently reach underneath and pull off the mesh speaker cover. It only clips in so don't worry about breaking anything.

    “it only clips”

    Broke 3/4 “clips” on the first try,

    you should be worried.

    Andrew King -

  3. WZIlPuNfIONyAwTj

    • Remove (4) screws (14 mm) with a PH1 screwdriver on the front panel by the speaker.

    • Be careful with these screws, as they can be stripped easily.

  4. BuaVNGSAJdsghTNF

    • Move the metal spudger around the front panel to remove any adhesive attaching the front panel to the device.

    • Pull apart the front panel from the device with help from the metal spudger.

  5. PGKlsQl3LwAmqdPE
    PGKlsQl3LwAmqdPE
    udF6fTRLhJeoCMlE
    Snl1fSd2Iw3GFSof

    • Detach a pin connector at the top of the device using a metal spudger to open up the inner components.

    • Detach (4) pin connectors inside using a metal spudger to separate the front panel from the rest of the device.

    is the battery permanent or can be replaced?

    Murray L. Berkowitz -

  6. IypmR34iOXmwWDKC

    • Remove (10) screws (10 mm) with a PH1 screwdriver on the display board.

  7. jHxNtHapSi4EYOXX

    • Remove the motherboard from the front panel.

    • If motherboard is difficult to separate, DO NOT force it. Check to see if all the screws were removed and proceed to remove the motherboard gently.

    Above in “Parts” you don’t mention motherboard. Since you are replacing the motherboard, woultn’t logic dictate this as a necessary part? And speaking of necessary parts, where would one purchase a motherboard for this referenced device?

    Rick Comtois -

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Nathaniel Brabham

Mitglied seit: 08/02/16

431 Reputation

Ein Kommentar

Nice guide. My Mondo Wi-Fi went flaky (read “died”) so I disassembled using this guide to check out the wi-fi adapter plugged into the internal USB port. Turned out the little adhesive they apply to keep the adapter in the USB port sort of flowed over the adapter. Cleaned the adapter and plugged into the USB port on the rear of the radio and I’m back with a working Mondo. Glad iFixit does more than just computers and phones and pads (though it seems the Mondo is really a little Linux box).

csiemen -