GuliKit KingKong 2 Pro Triggers Replacement

Geschrieben von: Dominik Schnabelrauch
  • Kommentare: 5
GuliKit KingKong 2 Pro Triggers Replacement

Schwierigkeitsgrad

Moderate

Schritte

19

Zeitaufwand

30 - 40 Minuten

Einleitung

Use this guide to remove the triggers in your GuliKit KingKong 2 Pro controller.

  1. U4Nrl5tNANSaohOE

    • Use a Phillips #00 screwdriver to remove the four 11 mm-long screws securing the back cover.

    Hi, do you know what size screw is used for the outer portion? mine is stripped and i need to buy a new one

    Kevin Dimas -

    What you should use is a PH #0 Screwdriver, not a PH #00

    Yamatoklok -

  2. 4t5vaEkQAXGRo4hI
    4t5vaEkQAXGRo4hI
    6lUsZPPxiGFoWCey

    • The back cover of the GuliKit Kingkong 2 Pro is held in place by plastic clips.

    • Insert an opening pick into the gap between the front assembly and the back cover at the bottom edge of the controller.

    • Tilt your opening pick downwards to widen the gap.

  3. IvVFAaDOIQUiEHBJ
    IvVFAaDOIQUiEHBJ
    eIRQjRCoOywgKyLn

    • Insert an opening pick into the gap between the front assembly and the back cover at the outside of the right controller handle.

    • Slide the opening pick along the gap to separate the front assembly from the back cover.

  4. Qndkw5TYTOrOCZFu
    Qndkw5TYTOrOCZFu
    Sb6u11Dd5eWQFPxv

    • Insert an opening pick into the gap between the front assembly and the back cover at the outside of the left controller handle.

    • Slide the opening pick along the gap to separate the front assembly from the back cover.

  5. UWSlp65iZQ6OQH5C
    UWSlp65iZQ6OQH5C
    KWdSHPQ3GAyERcja

    • Separate the back cover from the front assembly and remove it.

  6. TciOVpng5G2RLV5d
    TciOVpng5G2RLV5d
    SxAwGaRR2ZFU3bbG
    FxSjGqHCO62TXIbJ

    • It's not mandatory to remove the two vibration motors to remove the mainboard assembly. However, other repairs become much easier with the motors removed. If you want to leave the motors in place, you can jump straight to step 9.

    • Pull on the connectors themselves and not the cables to avoid damaging them.

    • Use the point of a spudger to disconnect the right vibration motor by pushing the connector straight out of its socket.

    • If you can't disconnect the vibration motor with a spudger, use a pair of blunt nose tweezers to pull the connector out of its socket.

  7. aMHLoLTxSCAX1TOw
    aMHLoLTxSCAX1TOw
    FHNqdSAQnT4kpsMo
    ymLPUJYHM2pFTJYg

    • Use the point of a spudger to disconnect the left vibration motor by pushing the connector straight out of its socket.

  8. kfNV6jyFLDB5AJXY

    • Remove the vibration motors by lifting them out of the controller housing.

  9. yF6kX1SpxIbFlM5v
    yF6kX1SpxIbFlM5v
    KoNRLSHNBRbutkCL

    • Use a spudger, an opening tool, or your fingernail to flip up the small, hinged locking flap on the interconnect cable's ZIF connector.

  10. dTXOkbZThCGYAuQO
    dTXOkbZThCGYAuQO
    EYPIQPII6HYFKRcy

    • Use a pair of blunt nose tweezers to disconnect the interconnect cable by pulling the cable straight out of the connector.

  11. cpAOxRGJ5MRJUIif

    • Use a Phillips #00 screwdriver to remove the screws securing the mainboard assembly:

    • Four 7.8 mm-long screws.

    • Two 11 mm-long screws.

  12. Z1EPXYJXEYt5V3o4
    Z1EPXYJXEYt5V3o4
    ZReMMIgEPAmIBKPH

    • Use a pair of blunt nose tweezers to remove the metal shield from the mainboard assembly.

  13. PgHHDOQ22cXUOh5g
    PgHHDOQ22cXUOh5g
    rACfkuWotWEoKllR
    b1GU2bsThlGub1jT

    • Remove the mainboard assembly by lifting it out of the controller housing.

    I highly recommend pulling off the joystick caps before removing this board, since the joysticky get caught on the other board. Alternatively, one can carefully slide back the mainboard, then unscrew and remove the triggers. Then the mainboard can be lifted up very easily. Accessing the trigger screws is a little tricky this way though.

    Sebastian Jost -

  14. xdAvAlTpKFe6ckdG

    • Take care not to puncture the battery with your tool—a punctured battery may leak dangerous chemicals or cause a fire.

    • Use a Phillips #00 screwdriver to remove the single 7.8 mm-long screw securing the battery frame.

  15. YT2lrwVCYhcNnuyO
    YT2lrwVCYhcNnuyO
    Qsb5eHjfMuEAlbNR
    aIVWUoBUhKVIgCMQ

    • Free the battery frame by lifting it off the plastic pins holding it in place.

  16. Dw1EaUvcPUKBeZfO
    Dw1EaUvcPUKBeZfO
    ItkjEoIXclEoj6Pv

    • Pull on the connectors themselves and not the cables to avoid damaging them.

    • Use a pair of blunt nose tweezers to disconnect the battery connector by pulling it straight out of its socket.

    • Remove the battery and its frame from the controller housing.

  17. nSLKHp2LC6yjRPbE

    • Use a Phillips #00 screwdriver to remove the four 7.8 mm-long screws securing the triggers.

  18. BOvvbO2XQbitiSPy
    BOvvbO2XQbitiSPy
    RbKGseHUBanEslyP
    Z1ANOKPPoAeEPNeJ

    • Use your fingers to lift the left trigger off its bracket.

    • Remove the left trigger.

  19. ddRMChOFp6nKNxvC
    ddRMChOFp6nKNxvC
    FNLLyBYsQRrXIppd
    uODTREH6pnUIC1rQ

    • Repeat the previous procedure and lift the right trigger off its bracket to remove it.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

Tinte & Feder

Dominik Schnabelrauch

Mitglied seit: 23/11/16

167866 Reputation

2 Kommentare

Do you know where to buy a replacement zr trigger? The Black piece of Plastic,as in your last picture ,is broken on mine.

Strumpfmaskenmann -

My Gulikit Kingkong 2 (non-pro) controller bought in Dec 2022 only uses PH01 screws. No PH00 ones. Otherwise this guide is very helpful for any disassembly you may want to do.

Sebastian Jost -