HP ENVY 5530 Gear for Scanner Arm Replacement

Geschrieben von: Elizabeth Surface
  • Kommentare: 2
HP ENVY 5530 Gear for Scanner Arm Replacement

Schwierigkeitsgrad

Moderate

Schritte

8

Zeitaufwand

20 Minuten

Einleitung

Gear allows the scanner arm to follow the grain track and scan the document. Before replacing the gear make sure the printer is unplugged.

  1. 6S4JObgM1b2aBOof
    6S4JObgM1b2aBOof
    cwL2Uhn3F1BFNKY2
    HsLIIhVEAkuTDLQh

    • Unscrew and remove the center 13mm T10 Torx Security screw using the iFixit screwdriver

    • Unscrew and remove the top right 13mm T10 Torx Security screw using the iFixit screwdriver

    • Unscrew and remove the bottom left 13mm T10 Torx Security screw using the iFixit screwdriver

  2. I3AeZtOJVuowp1Uv
    I3AeZtOJVuowp1Uv
    3sFNHAbETYIfpLrL
    yTjHZZRKLDDlZGAZ

    • Unscrew and remove the bottom 13mm TR10 Torx Security screws using the iFixit screwdriver

  3. aCoCUcJjTifmhF5h
    aCoCUcJjTifmhF5h
    fk1pAEsKAj6Un4WC
    p4Q3tSw3uDgup4nv

    • Unscrew and remove the top right13mm TR10 Torx Security screws using the iFixit screwdriver

  4. mWSBoHobiNMRrTKN
    mWSBoHobiNMRrTKN
    Csua1UjhSJeuYSM1

    • Unscrew and remove the upper 13mm TR10 Torx Security screw using the iFixit screwdriver

  5. KBGPQ4IALo6SSkoM
    KBGPQ4IALo6SSkoM
    xuyVFJEteOPqwj2b

    • Remove the scanner lid and plate (top cover).

    • Locate the Scanner Arm Actuator.

  6. Cuy1sGRS6FKZPNJP
    Cuy1sGRS6FKZPNJP
    SD4cCO6aT2HNcQud

    • Locate the Scanner Arm Accuator and remove.

  7. MgW5odsiJN6FZVQs
    MgW5odsiJN6FZVQs
    XCKIxgGnSScMrY2o

    • Unscrew and remove the 13mm TR10 Torx Security screw in the center of the gear using the iFixit screwdriver

  8. pHSRcCNu5AYYFlgM
    pHSRcCNu5AYYFlgM
    a2V1WhuleblbSsRC
    OD5HoM5itE3IkLET

    • Locate the white gear and remove.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Elizabeth Surface

Mitglied seit: 27/08/15

1447 Reputation

2 Kommentare

It is not possible to get to the bottom two screws out without tilting the scan bed/cover back more. To that, I had to disconnect the swing arm on the right side of the scanner bed/cover. After that, all worked smoothly. Thank you.

Ron -

I have this model too and the scanner quits scanning - usually in mis-scan. I then have to cancel and shut down the machine. Lifting an end of the machine and dropping it (that's right) usually brings the scanning operation back to life once power is restored. I'm curious - what were the symptoms the author of the guide ran into? Why the gear? Why not the electronics? Where can one get the gear?

Joel Bacon -