HP EliteBook x360 1030 G3 Speakers Replacement

Geschrieben von: Mahn Hein Ko
  • Kommentare: 0
HP EliteBook x360 1030 G3 Speakers Replacement

Schwierigkeitsgrad

Moderate

Schritte

13

Zeitaufwand

20 - 30 Minuten

Einleitung

This guide is for HP EliteBook x360 1030 G3. Before you replace the speakers, try to troubleshoot the problem first. Since the speakers are directly linked to the motherboard, so you may need to update your driver and may fix the speakers. If you think troubleshooting is not working, follow this guide to replace the speakers.

  1. 6jic6bxJFvToOpWM

    • Be sure to power off and unplug your device before you begin your repair.

    • Close the laptop and flip it so that the screen is on the surface of the table and the back plate is facing you.

    • Remove the 3.3 mm screw near the top of the hinge using a T5 Torx screwdriver.

    • Remove the remaining four 7.3 mm screws using the same screwdriver.

  2. 4cZiMcfhh5M6foMq

    • Separate the bottom cover from the laptop, starting from the upper corner and working your way around the edge.

    • The plastic fastening may make cracking sounds when separating, but this is normal.

  3. NqfEFVMoP62immiw

    • Remove the five 3.7 mm screws that are holding the battery in place using a Phillips #00 screwdriver.

    • Be sure to keep the screws organized because they will be reused for the next battery installation.

  4. ykGDqLpZDwdoIniE
    ykGDqLpZDwdoIniE
    E6nX31WTODN2yeCZ

    • Carefully pull the white plastic battery connector towards you until it is removed from the port.

    • Be sure not to pull using the wires; doing so may cause damage.

  5. jVVOghidaXS6alBS

    • Gently lift the battery out of its place.

  6. Xk5hrOJyXogKwN4S
    Xk5hrOJyXogKwN4S
    PymZK6QA1NRe1561

    • Remove the six 1.95 mm JIS #000 screws that secure the metal frame of the touchpad.

  7. GLF1ReJQyJCkkvqT
    GLF1ReJQyJCkkvqT
    EArsZm3CXIEg3fnh
    QblrQtvRt2jMYLvA

    • Lift the small white ZIF connector from the front using a spudger tool or your finger.

    • Only lift the white hinge securing the Flexed Flat Cable making sure the unit stays secure to the board.

  8. g1DohdlyqbNXcTkW

    • Pull the yellow and orange striped ribbon away.

  9. eGlRlqMaOrugwjq5

    • Lift the touchpad up from the computer board by the metal frame.

  10. NYy3AHNFMVZ5aGSp
    NYy3AHNFMVZ5aGSp
    KbEmUYdmCHbtHAJY
    D3xKafZOtTKGthB5

    • Remove the two 3.52 mm JIS #000 screws from the left speaker.

    • The speakers are magnetic, so carefully remove from its magnetic place.

  11. jeaUvpHLVkiBQIuG
    jeaUvpHLVkiBQIuG
    RwETgVGHeE6OIfLP
    LEAyc5HsxouexOuD

    • Follow the red and black wire and you will see the two wire brackets.

    • Use the spudger to slide it and push the wire out of the brackets, then take it out.

  12. 4vsCoW6dG1meTY1c
    4vsCoW6dG1meTY1c
    DFhSel4FNDZHNkTv
    iteDoLPjIvCNJTMp

    • Remove the two 3.52 mm JIS #000 screws from the right speaker and carefully remove from its magnetic place.

    • Remove the black tape with your hand that is around wire.

    • Use the spudger to slide it and push the wire out of the brackets, then take it out.

  13. uWEn5ExtkR1yNmjH
    uWEn5ExtkR1yNmjH
    yWhwAHXPNQHPb4BF
    gNyO3wgMklGi1tEH

    • Remove the black tape from the mother board with your hand.

    • Unplug the green and white wire plug gently, and the red and black wire plug gently with your hand.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Mahn Hein Ko

Mitglied seit: 17/05/22

109 Reputation

0 Kommentare