HP ElitePad 1000 G2 Audio Jack Replacement

Geschrieben von: Christopher Graveline
  • Kommentare: 9
HP ElitePad 1000 G2 Audio Jack Replacement

Schwierigkeitsgrad

Moderate

Schritte

7

Zeitaufwand

5 - 10 Minuten

Einleitung

To make sure that replacement of the audio jack is necessary follow these troubleshooting steps before using this guide.

  1. Y22liYDNHjWXfYWT
    Y22liYDNHjWXfYWT
    XLIKLge56vsTFKcZ
    2NV5yjKuWOhwxe14

    • Before disassembling the tablet: make sure the tablet is off, disconnect the power cord from the tablet, and disconnect all external devices from the tablet.

    • Using a Phillips #00 screwdriver, remove the two Phillips PM 1.4×3.2mm screws located next to the charging port.

    have a safe place to save the 8 tiny screws. the screwdriver will need a thin shaft to get inside the holes.

    Teddy Sam -

  2. ZeRo2QYImvbZ5NmH
    ZeRo2QYImvbZ5NmH
    3dWSMfVsm6HT34Ju
    tFIJnfWZJMW3KDma

    • Place the suction cup on the lower right corner of the tablet display glass, making sure to place the suction cup inside the edges of the border of the display glass.

    • Insert a plastic pick in between the display and the tablet case. Then use a plastic removal tool to separate the display further.

    • Pull on the suction cup while using the prying tool to separate the display from the tablet.

    • Gently lift the display from the tablet in order to avoid damaging the cables.

    Might want to use the spudger tool to pry the screen up. We had difficulty using the pry tool. to pull up the screen.

    Cameron Gow -

    display is held to the base by 3 magnetized tips on the right edge and 4 on the bottom edge (charging port) of the display. the ones on the right are at the center and at each corner before the display curves. on the bottom edge, 2 are at the corners and the other 2 are 1.5” inward. the top and left edges are friction tips. prying along the edges releases the magnetic tips from the base.

    Teddy Sam -

  3. oDy42BFrEGZsNiv2
    oDy42BFrEGZsNiv2
    KNPq1K2ay1CsUawq
    tI1vKplNVQHiutAk

    • To disconnect the cables, use the spudger tool to gently pull back on the black tab located on the side of the connector while gently pulling the cable.

    • Release the zero insertion force (ZIF) connector to which the TouchScreen cable is attached, and then disconnect the TouchScreen cable from the system board.

    Need to Add the spudger tool and differentiate between the black spudger tool and the blue plastic pry tool.

    Cameron Gow -

    When disconnecting the cables we found that the wording “ push the tab” was confusing. We had to pull up the black tab for the ribbon cables to disconnect.

    Cameron Gow -

    i didn’t know what a spudger tool was but didn’t find any black tab to push or pull. both of my cables were taped on the bottom and top. they also had adhesive on the bottoms. i removed the tape, gently lifted the cables away from the silver cover the were stuck to and pulled the cables out from their zif sockets.

    Teddy Sam -

    i figured out how the zif sockets work and am correcting my previous comment. on my unit, the zif sockets are black and the release levers are white. i “opened” the zif sockets by flipping up the white edges that were furthest from the cables. i removed the tape, gently lifted the cables away from the silver cover they were stuck to and pulled the cables out of the zif sockets.

    Teddy Sam -

  4. KbSxlDegIdLbOrbv
    KbSxlDegIdLbOrbv
    DgwXTrwBZRVMg5YC

    • Release the ZIF connector to which the display cable is attached, and then disconnect the display cable from the system board.

    Here, be sure to include the spudger you’re using.

    Alex Watkins -

  5. BT2iuCq6WgRbXUMf
    BT2iuCq6WgRbXUMf
    1iU1OAh5MLRXTj4P

    • Remove the display from the tablet.

    The second shot here is blurry. Do you have a clearer version?

    Alex Watkins -

  6. eTSyBRMCdlMqGqIk

    • Locate the audio jack board.

  7. uJnVPUSICBUIApMr
    uJnVPUSICBUIApMr
    Ij1Qi153HjXpF6cF
    xjTaKjnP1M6TtXVI

    • Disconnect audio jack board cable from the motherboard.

    • Remove the two Phillips PM 1.3x2.0mm screws that secure the audio jack board from the housing.

    • Remove the audio jack board.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Christopher Graveline

Mitglied seit: 08/07/19

178 Reputation

0 Kommentare