HP Elitebook 820 G1 Fan Replacement

Geschrieben von: Alex
  • Kommentare: 3
HP Elitebook 820 G1 Fan Replacement

Schwierigkeitsgrad

Moderate

Schritte

16

Zeitaufwand

25 - 30 Minuten

Einleitung

Fans are mechanical and fail over time. If the laptop is easily overheating or the fan is not heard, the fan is at fault. This guide explains how to replace the fan.

  1. gRrXdhBP1S4elQ1l

    • Ensure the laptop is completely powered off and power adapter is unplugged before removing the battery.

    • Turn over laptop so that the bottom is showing.

    • Unlock the latch.

  2. KmNtlqUOgEkOQx5W

    • Remove the back cover and you will then be able to see the battery.

  3. LYkwpIEDtOrrMAyB

    • Unlatch the two latches securing the battery in the case.

  4. 5KvM53UkwkRqRQLr

    • Use a plastic opening tool to lift and remove the battery.

  5. uWZdEBBOERG2pMCB

    • Remove the hard drive by unscrewing the four 8mm screws with the T7 philip's head.

    In this step it is also important to unplug the WiFi antenna.

    tomasbasak -

    Hello, I would like to complete this tutorial, but I am not very knowledgeable on computer parts, so I have no idea where the wifi antenna is (in this picture) or what it looks like (I tried to google it tho), I’d be very thankful for a reply. :)

    Flora K -

  6. ZADZTQRoEHx6UYxV

    • Pry off ten rubber paddings on the outer edge of the laptop to reveal the torx screws.

    • Unscrew the ten 8mm torx screws that are under the rubber paddings using the T7 tip torx screwdriver.

  7. ONtfvcOXEDq11TEg

    • Remove the two 4mm screws indicated by the M2.5X4 using the J00 tip screwdriver.

    • Remove SD card cap by just sliding out to reveal one screw.

  8. 6Kv4QhPSHPaMky3A

    • Remove the two 3mm screws indicated by the M2.03 using the J00 tip screwdriver.

    • Remove the 4mm SD card screw using the J00 tip.

  9. DPX4fTVNoIAZSUNV

    • Remove the one 4mm fan screw using the J00 tip screwdriver.

    • Remove screw and metal plate to expose ribbon cable connector.

  10. sPEeQSSHAlvRNg6c

    • Use an opening tool to pry up the ribbon connector to disconnect.

  11. uIVPrIBbFUBVPhFH

    • Turn laptop over back to normal position as shown in the image.

    • Use opening tools to pry up keyboard.

    • When prying up keyboard, be sure to start near any corner of the keyboard.

    • There are two ribbon cables that must be disconnected before fully removing keyboard.

    It is preferable to follow step 6 from "Keyboard replacement" to remove the keyboard as it shows that "4 tabs are located at the top of the keyboard, which lock it in place".

    See HP Elitebook 820 G1 Tastatur tauschen

    John Geerlings -

  12. ZdYv5K5OdyH4RdOM
    ZdYv5K5OdyH4RdOM
    1AANbvWXCcrr1TK2
    G3SYcRVxOyvONimJ

    • Carefully lift keyboard on one side to expose the two ribbon cables.

    • Use an opening tool to lift up the locking clip and unplug the two ribbon cables.

  13. UehuABZOhmjVWMZ1

    • Remove the two 4mm screws centered notated by the keyboard logo using the J00 tip.

  14. bZdsMIPeTbE6aKxq
    bZdsMIPeTbE6aKxq
    BygrShpNdCsDcMZs
    Ww1YaMDQxE5Uqacp

    • Once keyboard has been fully removed, the system case containing the motherboard can be lifted out easily.

    • The display is connected to the shell of the laptop.

  15. w3JWdGaKVcchFOfI

    • Unplug fan cable by pulling away from its connector.

  16. FENQIXcaQ1Odvc1E

    • Unscrew the two 6mm fan screws using the J00 tip.

    • Fan screws are encased in springs and cannot be removed.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Alex

Mitglied seit: 14/02/18

217 Reputation

0 Kommentare