HP Pavilion G60-120US Display Assembly Replacement

Geschrieben von: Won Chan Park

Kommentare: 2

HP Pavilion G60-120US Display Assembly Replacement

Schwierigkeitsgrad

Moderate

Schritte

Zeitaufwand

30 Minuten

Einleitung

This guide shows how to go about removing the display assembly from the HP Pavilion G60-120US and installing a replacement. This will also enable users to access multiple parts of the laptop.

Werkzeuge

Schritt 1

Make sure the laptop is turned off.
Turn the laptop over to reveal the battery.

For the introduction, rephrase: “To gain access to the motherboard component, it is first necessary to remove the battery, screen, and motherboard cover. This pre-requisite guide walks users through the process of removing these components in order to access the motherboard. Replacing the motherboard is an important task as it holds…..”

Sandy Branham - 24/10/19

Schritt 2

Slide and hold the battery release switch to the left to release the battery from the device.

Schritt 3

While holding the battery release switch, grab the battery and pull it upward gently.

Schritt 4

Using the Phillips #0 screwdriver, remove the seven 4.0mm screws on the battery compartment of the laptop.

Schritt 5

Using the Phillips #0 screwdriver, remove two 4.0mm screws from the hard disk cover.
Remove the hard disk cover.

Schritt 6

Remove the hard drive by pulling gently and disconnecting the hard drive from the laptop.
Gently pull on the black and red wiring on the bottom left to separate the wire from the component.

Schritt 7

Remove the two 4.0 mm Phillips #0 screws from the hard disk compartment.

Schritt 8

Using the Phillips #0 screwdriver, remove the two 4.0 mm screws from the memory card cover.
Remove the memory disk cover.

Schritt 9

Using the Phillips #0 screwdriver, remove the 4.0 mm screw from the Wi-Fi chip cover.
Remove the Wi-Fi chip cover.

Schritt 10

Using the Phillips #0 screwdriver, remove the two 3.0 mm screws securing the Wi-Fi chip in place.
Grab the Wi-Fi chip and pull up gently to the left to disconnect it from the laptop.

Schritt 11

Disconnect the two wires connecting the chip's base.
Remove the Wi-Fi chip.

Schritt 12

Using the Phillips #0 screwdriver, remove the seven 4.0 mm screws on the bottom of the laptop.

Schritt 13

Turn the laptop back to its upright state.
Insert an opening tool into the upper right corner of the keyboard and gently lift it to separate it from the laptop.
Be sure not to apply excessive pressure to prevent the bending and breaking of the keyboard.
Do not pull the keyboard all the way out because there is a wiring connection under the keyboard.

Schritt 14

Grab the wiring and gently pull it out to disconnect it from the laptop.
Don't use excessive force.
Remove the keyboard.

Schritt 15

Insert an opening tool into the top right side of the corner, and gently lift the rest of the cover to separate if from the laptop.
Avoid using excessive force which may break the cover.
Do not completely pull out the cover; there is a wire still attached to the laptop.

Schritt 16

Using your fingertips, detach the ribbon cable by gently lifting up the black tab located on the bottom end of the cable.
Separate the cable and remove the cover.

Detach the wire by gently lifting up the black component.

Once the wire has been detached, remove the cover.

(This first instruction could also use a bit more detail — where is the black component located in relation to other items? Also, action shots would be helpful here.)

Sandy Branham - 27/10/19

Schritt 17

Remove the mouse and touchpad cable by lifting the black tab and gently pulling the cable out.

Schritt 18

Detach the white screen wiring on the bottom left side by gently pulling out.
Detach two black screen cables on the middle left side by gently pulling out the cables.
Pull out the black cable on the upper right side of the laptop.
Use gentle pressure while removing the wires.