HP Slate 7 4601 Battery Replacement

Geschrieben von: Zachary
  • Kommentare: 12
HP Slate 7 4601 Battery Replacement

Schwierigkeitsgrad

Easy

Schritte

12

Zeitaufwand

10 - 15 Minuten

Einleitung

After many times of attempting to recharge the battery with no success, it may be time for your Slate's battery to be replaced. This repair guide is the primary step for all future repairs on your HP Slate, and is a basic process to master. In this guide, you will be removing the following:

  1. Back Cover
  2. Battery

Prepare your required tools, a new battery for your tablet, and set aside about 10 to 15 minutes to delve into the inner workings of your HP Slate.

  1. oyYuZHynPkfZKdpp
    oyYuZHynPkfZKdpp
    VWHBYdxAmNLBBLEq

    • Begin your replacement by using a T3 or T4 Torx screwdriver.

    • Remove the two 1.4mm x 3mm Torx Head screws at the top of the device.

    On the HP 10 Plus 2201 there are no head screws. I used the spudger to 'carefully' separate the case. There are little snaps on the inside of case that will separate with little pressure on spudger.

    RB Richter -

    I used these directions to replace HP Plus 10 2201 battery. I bypassed speaker installation.

    RB Richter -

  2. E632GhJNVWIoWOEB
    E632GhJNVWIoWOEB
    NwLGaSd4dAfVDmbN

    • With the pointed end of the spudger, remove the thin metal band.

    • It is easiest to remove the metal band through the headphone opening.

    On HP 10 Plus 2201 there is no metal band. The case simply unsnaps apart.

    RB Richter -

  3. tTBhCKPal6DwANtH
    tTBhCKPal6DwANtH
    ILOygovSYpSNDSVq

    • Using the flat end of the spudger, pry back the rear plastic cover.

    • As you work your way around the edge, several "pop" noises will be made. These noises are caused by the plastic clips coming undone.

    This is basically how I opened my HP 10 Plus 2201. "Using the flat end of the spudger, pry back (apart) the rear plastic cover from tablet.

    RB Richter -

  4. pQJLZCgkDpJZBawG

    • Remove the rear cover.

  5. GCKXs1DX2SJWPbW4

    • Locate and remove the yellow tape covering the red and white speaker wires.

    The inside of my HP 10 Plus 2210 looks similar but not exactly as this illustration

    RB Richter -

    The battery connections weren't the plug in type. The three battery battery wires (red, white, & black) were soldered into place,

    RB Richter -

  6. p6wnyhUAepKVTRWM
    p6wnyhUAepKVTRWM
    b6LxfDQBDFXElUtp

    • Using the pointed end of the spudger, push both sides of the speaker wire connector out of its base.

    • Push the same amount on both sides of the connector to avoid jamming or twisting its metal pins.

    • Do not yank or pull on the speaker wires, since they are fragile. Only push on the white connector.

    Do not pull on wires. Never force anything.

    RB Richter -

    note the route of the speaker cables round the battery

    Alan Boddey -

  7. P1WpoOHlYsk4CUlq

    • Gently pull back the foil covering the gold charging port ribbon.

    Hpcom Support Helps HP Printer users to download and install All Hp Printers drivers. We also provide all possible solutions to fix hp Printer problems. If you face any issue in install Hp printer driver or having other problems with the hp Printer, you can follow our 100 % working solutions. In case you can’t able to continue printing, then feel free to contact us. We are happy to serve you.

    hpcom us -

  8. ihlYYMpBQlsYaciH
    ihlYYMpBQlsYaciH
    rXofslcwLldga2Ak

    • Using the flat end of the spudger, lift up the black panel covering the charging port connector.

    • Gently slide the charging port ribbon out from its housing.

    • It may be easier to use the pointed end of the spudger than your fingers.

  9. pIQfU5TndgTRjywE

    • Lift gold charging strip away from the battery.

  10. BQi2f4JckEJ4nA1s
    BQi2f4JckEJ4nA1s
    SpZ4dB1IkVpmgcGE

    • Push the white battery connector out of its housing using the pointed end of the spudger.

  11. 3SmKVAOfIeeQxlRS

    • Using the #00 Phillips Head screwdriver, remove the 5 screws holding the battery in place.

    • The four 1.75mm x 3mm silver Phillips Head screws circled in red are interchangeable.

    • The black 1.75mm x 4mm Phillips Head screw must go back to the same spot during reassembly.

  12. nXdHS2EjOpFk3nCn

    • Lift battery out of its place and set aside.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Zachary

Mitglied seit: 14/04/14

1441 Reputation

3 Kommentare

Buenas tardes, como están? Consulta, la batería se puede reemplazar por otra genérica, existe algún repuesto?

Javier Sanchez -

Thanx for this amazing demo steps. Sir i need battery of this tab, coz i cant find this battery anywhere then someone told me to go online purchase it wil you so i decided to go online n finally i found ur page so plz arrange me the battery of this tab. My HP Slate 7 battery is not charging . I m from pakistan n my email is aasifbrothers79@gmail.com. Sir i m looking forward for ur kind reply .Thanx

Regards, Asif Sultan

Asif Sultan -

where do i buy the battery in india… there is a site Maxbhi, I ordered the battery, they never send the battery neither returned the money…

Kapil Baidya -