HP w2216h Video Port Board Replacement

Geschrieben von: Branflakes222
  • Kommentare: 3
HP w2216h Video Port Board Replacement

Schwierigkeitsgrad

Moderate

Schritte

15

Zeitaufwand

Keine Schätzung

Einleitung

The HP w2216h has 3 signal output ports. One is an HDMI port which outputs video and sound. One is a VGA port which outputs video. And one is an audio port for external speakers. Each of these ports are removed as a single part.

  1. vktZgvmRpadN4BOJ

    • 'Make sure you are grounded, the power supply is not connected and you are wearing safety goggles.

    • Use the Philips #000 screwdriver to remove the 4 round12mm screws on the back panel.

  2. YP5CgKJY5eIEbUuk
    YP5CgKJY5eIEbUuk
    uA5ZDATn2M6p4DOv

    • Using a Philips #000 head remove 2 flat 12 mm screws above stand mounting bracket.

    • Using a PH1 Philips head with the 150 mm flexible extension remove 1 Philips head screw under the stand mounting bracket.

    • Stand will easily pull off.

  3. dbluiEhRGo4kXcNp
    dbluiEhRGo4kXcNp
    QlyNqVlQRps2ZufC
    3EiqUthsIUDD6KYt

    • Do not put the metal spudger between the metal and the glass. It needs to go under the bezel and above the metal.

    • Turn monitor so that the screen is facing you.

    • Pry the black bezel from above the metal by placing your metal spudger between the bezel and the metal and twisting the tool slightly.

    • The best places to pry are in the lower left and lower right corners of the black bezel.

  4. xKeyGUimU2ZLQfjf
    xKeyGUimU2ZLQfjf
    MdPvDLhdExAhk3xS
    TDIPBYlaJQbRYBEQ

    • Be careful of the wires attaching the power button and the control buttons. Show extreme caution to ensure the button is not damaged.

    • Lift the screen assembly from the plastic housing from the corners.

    Should it be "underneath one of the device's corners"?

    Daniel Servant -

    You might want to add a note letting users know that they should be careful of the wires attaching the assembly to the housing.

    Daniel Servant -

    You may also want to note that the card for the power button slides out when you lift this assembly so the user might need to be told to slide the card back into its slot when installing the new screen. ( A picture of this would be a good idea)

    Daniel Servant -

  5. SFkianqZcysu6GV1
    SFkianqZcysu6GV1
    dhdynObANLcBjUKI

    • Remove the 4 connectors from the left side of the monitor on the back.

  6. AweLVWlsIQxHWCUu
    AweLVWlsIQxHWCUu
    Db1oHYjQneKAnEeB
    FftQvMeWEJwWZkjA

    • Lift the gray tape of the top of the monitor to expose the ribbon cable.

    • Remove the ribbon cable by sliding the connector towards the center of the screen assembly.

    • Lift the reflective tape next to the gray tape.

  7. cjZFqSVFM1FbAjrV
    cjZFqSVFM1FbAjrV
    wmKy3fPNfVkC5q6o
    ARGx5aY1DeP2W5U5

    • Remove the 4 PH1 8mm Philips round screws on the outer edge of the screen's assembly.

    • Lift the screen from the screen assembly.

  8. FBEDeRYkPZEceMQR

    • Remove the tape holding each speakers wire to the screen assembly.

  9. kNLZTiYFOcaRKOko
    kNLZTiYFOcaRKOko
    KERCswBfyKRW4gKk

    • Remove the two 8mm Philips #000 head screws on each speaker.

  10. DyXvXXb4NjUgcmkG
    DyXvXXb4NjUgcmkG
    tWpylYUAnjurbhuP

    • Remove the speakers by lifting them vertically from the screen assembly.

  11. TPTMHTSgnPDGBYYu

    • Remove the cables that connects the speakers to the signal output board.

  12. pGiA2wPVZJjVKq1P

    • Remove the single Phillips #000 head screw above the HDMI port .

  13. jKRsQNZS1ytS54tB

    • Remove the two 2.5mm hex screws on either side of the VGA port

  14. QkWksMfRnGSrtBSe
    QkWksMfRnGSrtBSe
    2AshwMRpRGvR4oGH
    sOuBxm6eFvZnVPTu

    • Remove all 8mm Phillips #000 screws holding the board in place.

    • Remove the ribbon cable towards the bottom of the board by sliding the cable away from the board.

    • Remove both wire busses still on the board.

  15. BQF5KVMUmeHePQ1B

    • Lift the board out of the screen assembly by first pulling the board away from the wall where the ports mount, then upward.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Branflakes222

Mitglied seit: 25/03/16

393 Reputation

0 Kommentare