HTC Vive Pro Outer Shell Replacement

Geschrieben von: Sam Omiotek
  • Kommentare: 0
HTC Vive Pro Outer Shell Replacement

Schwierigkeitsgrad

Moderate

Schritte

16

Zeitaufwand

1 - 2 Stunden

Einleitung

Follow this guide to replace the outer shell of your HTC Vive Pro.

Power off and unplug your headset before you begin your repair.

  1. aMNZPqQCqvBpYVBr
    aMNZPqQCqvBpYVBr
    2t1YpoDa16u3a6nw

    • Rotate the head strap forward as far as it will go.

  2. lGRGmrJqbaNo2Ngy
    lGRGmrJqbaNo2Ngy
    tWWbSxVKBHuNwFNq

    • Unplug the All-In-One Cable from your headset.

  3. HbQvVLZ6kJDOwNRY
    HbQvVLZ6kJDOwNRY
    gXqSBAhFSAFT2PXt
    2NxZbAVObNCtX5Cs

    • Remove the All-In-One Cable from the cable guides along the left side of the head strap.

    • During reassembly, connect the All-In-One Cable to the headset before routing it through the cable guides. This will ensure it has the right amount of slack.

  4. 3dG4uV5DpUAQZptQ
    3dG4uV5DpUAQZptQ
    YiMWeYhExTRMVKFO

    • Separate the top strap from itself where the velcro secures it.

  5. VLPdIX14F6iiruXO
    VLPdIX14F6iiruXO
    UmwroeIuZueAKbbW
    e5EtHVxxujdCPHxB

    • Peel back the Velcro securing the rear of the top strap.

    • Feed the top strap out through the head strap to remove it.

  6. HcrR5RsAx4PE1h5j
    HcrR5RsAx4PE1h5j
    5vWrMBaqmgo4UBuT
    dCT1YqKf4opHuM2s

    • Feed the top strap through the clip on the headset to fully remove it.

  7. LnRydVZX5GycMC3o
    LnRydVZX5GycMC3o
    mPWInBOiUxUoIWHk
    32lhPiKJihIMHrPC

    • Peel off both front side foam pads to uncover the speaker wires.

  8. MM2PomssV1GIH2k1
    MM2PomssV1GIH2k1
    hTtmb141iJw5OJFm
    ZAfuS6wZT1FGWjtG

    • Insert the pointed end of your spudger behind the square rubber spacer next to each headphone screw.

    • Gently pry the rubber spacers out of the head strap.

    • Be careful not to accidentally pry any of the speaker wires under the rubber spacer.

  9. CVbX4PPWpfuB3Lev
    CVbX4PPWpfuB3Lev
    gTHLVQVxN2kPBLhD

    • Use the pointed end of your spudger to pry up and disconnect both the left and right headphone speaker wires.

  10. jyvLOIRiavsuSgk3
    jyvLOIRiavsuSgk3
    sAPbTeRiI1VYx2yZ

    • Use a T6 Torx screwdriver to remove the two 12.1 mm screws (one on each side) securing the head strap to the headset.

    • Use a T5 Torx screwdriver to remove the following screws securing the head strap to the headset:

    • Four 3.9 mm screws (two on each side)

    • Two 4.1 mm screws (one on each side)

  11. 2KDUshEaMsb6IDTc

    • Remove the two plastic spacers underneath the previously removed screws from the headset.

  12. sIRdYNZpryGVtKfP
    sIRdYNZpryGVtKfP
    bPQpTY5jgpl5qIYQ
    U6AlJRrlhEUijfEP

    • Thread the headphone speaker wires out through the ends of the head strap.

  13. 1ISX4R22ASwnm5lV
    1ISX4R22ASwnm5lV
    S2NiObBZcMuvouI3
    dp21RZjHb4jZCsOe

    • The four screws securing the outer shell are covered with black stickers. If the stickers are difficult to remove, simply press your T6 Torx driver through them.

  14. pMgQ3ESQYRMklI6h
    pMgQ3ESQYRMklI6h
    JSWyBhAPsYgNKyUJ

    • Use a T6 Torx screwdriver to remove the four 3.9 mm screws (two on top, two on bottom) securing the outer shell to the headset.

  15. hUpUUiYRQaNyZS1h
    hUpUUiYRQaNyZS1h
    4OmDH5IcLtYfHuKI
    GFD4eIlBGPyIclaF

    • Insert an opening pick into the crease between the two halves of the outer shell.

    • Slide the opening pick through the crease to dislodge the clips securing it to the headset.

    • Only insert the opening pick as far as necessary. There are ribbon cables underneath the outer shell.

    • Continue sliding the opening pick through each crease until all clips have been dislodged.

  16. rtCGfAhMFHmN1nRU
    rtCGfAhMFHmN1nRU
    FLpF42bklI4xcbfe
    DnhCYUjWyraOYKFI

    • Carefully slide each half of the outer shell off of the sensor array.

    • Use caution not to snag any of the ribbon cables underneath.

Abschluss

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow the above steps in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our Valve Index Answers community for help.

Tinte & Feder

Sam Omiotek

Mitglied seit: 25/02/19

59342 Reputation

0 Kommentare