Hoover Power Path Pro Advanced Belt Replacement

Geschrieben von: Jose Andres Gonzalez Valdes
  • Kommentare: 13
Hoover Power Path Pro Advanced Belt Replacement

Schwierigkeitsgrad

Moderate

Schritte

8

Zeitaufwand

10 Minuten

Einleitung

The belt on the Hoover Power Path Pro Advanced allows the brush rolls to spin while the power is on. If the brush rolls are not spinning, then it is likely that the brush rolls need to be replaced.

  1. SgdWZwko3mNtoRpV
    SgdWZwko3mNtoRpV
    wBXwy15gusuhIIRp

    • Unplug the vacuum cleaner from the wall outlet before starting. Make sure the water tanks are empty.

    • Lay the cleaner down horizontally with its wheels closest to the floor.

    I have to rollers on mine.

    poco24 -

    I have two rollers on mine.

    poco24 -

  2. jP6URHTkpRHTRo4V
    jP6URHTkpRHTRo4V
    vQlKGTECQAYyD1Xv

    • Hold the lower brush roll with both hands and pull outwards until it is detached.

  3. Q6FuDmTHxFDL2SEu

    • Unscrew the 6 marked screws using a Phillips #2 head screwdriver.

    • Remove the brush roller.

    Removing long roller brush is not required and can’t be done at this point because of belt.

    frank wilbanks -

  4. nYTg2MiDKoAWRy2H

    • Use a long #2 Philips head screwdriver to remove the 8 numbered screws on the bottom of the cleaner.

    The 8 screws are not all shown here. There are arrows with numbers pointing at all of them on the dark plastic. The two shown here in red are labelled on the clear plastic.

    jschaudt -

  5. TUYGLNuMPIpNAKaC
    TUYGLNuMPIpNAKaC
    Gt1nRALsf1BNN2Q2

    • Pull the red handle shown to remove the front suction unit from the cleaner.

  6. Vd6qLU3yMNqPErQY

    • Unscrew the Phillips #2 screw at the bottom of the hose.

  7. TiCbgh3SUrKquanl
    TiCbgh3SUrKquanl
    aqyqIVeLBqAOEPHw

    • Push down on the handle release button. Pull and disconnect the edge of the top cover on the side of the handle release button.

    • Repeat the above step for the "On/Off" button.

    • When pulling the handle release button, make sure the top of the cleaner does not fall.

    What a load off bollocks following this instruction broke my Hoover

    Stewart Hogg -

    I followed your instructions and after pressing the release button and the start button erasing the clips broke my Hoover as it's not as easy as you

    Stewart Hogg -

    It is impossible to remove the top cover...!!!!! I'm breaking the vacuum!!! you need to give better instructions!!!

    Zulma Ossandon -

    This guy forgot about removing the entire underside first...also snapped off a plastic screw casing. Bollocks is correct. There should be 10 or 11 steps. Take off the bottom casing, about 7 screws I believe.

    Jane Blevin -

  8. CueN1U2cIPOei5KO

    • Gently grab the belt and pry it off from the rollers.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Jose Andres Gonzalez Valdes

Mitglied seit: 23/01/18

682 Reputation

5 Kommentare

Who the heck made this so hard,

Roy Merlino -

Day 5 and 4 people, I still can’t lift the top off to be able to replace belts. Is there a video

Roy Merlino -

Just understand there are more screws to remove then what is described in these 8 steps. Once you removed ALL the screws then the plastic lid comes right off.

Neil Sullivan -

How the back do you put the too belts on and seeing how the bag came with two and both were wide what size is the one that goes around the roller the other one control the circle brushes this is one of the most difficult belt change I've bad and I'm counting on car to

Loretta Staley -

There is only 8 screws you need to remove. The diagram makes it hard to know but there are two top ones Directly under the brush ! Once you get them out then comes off no problem at all.

Chris Harnish -