How to Loosen the Control Panel for the Honda 3000 Watt Inverter Generator EU3000IS1AWK

Geschrieben von: Arthur Shi
  • Kommentare: 0
How to Loosen the Control Panel for the Honda 3000 Watt Inverter Generator EU3000IS1AWK

Schwierigkeitsgrad

Moderate

Schritte

15

Zeitaufwand

Keine Schätzung

Einleitung

This guide shows how to loosen the control panel for the Honda EU3000IS1AWK 3000 watt generator.

This is a prerequisite guide! This guide is part of another procedure and is not meant to be used alone.

  1. UbGMSPUHmu5Emipg
    UbGMSPUHmu5Emipg
    EOqTsUAtCi2KFHFw

    • Before you begin, make sure the generator is off and cool to the touch.

    • Use a large flathead screwdriver to unlock the maintenance cover.

    • Open the maintenance cover.

  2. sJT2NiSJDvqIrsat
    sJT2NiSJDvqIrsat
    CGOaGS1UbALvMXom

    • Use a Phillips screwdriver to remove the screw securing the spark plug cover.

    • Remove the spark plug cover.

  3. PQCWqaPkWnK4k6CD
    PQCWqaPkWnK4k6CD
    EoOtaOPaXQtnwgWu

    • Grab the plastic housing at the end of the spark plug wire.

    • Pull firmly to disconnect the wire from the spark plug.

  4. 23thAcA2vMUnJWdU
    23thAcA2vMUnJWdU
    C5yxoojJaXjxcEnE

    • Turn the fuel valve to the cutoff position.

  5. iDvNAmrIrrmIpxK6
    iDvNAmrIrrmIpxK6
    P6XwTuMvPDD4ye2E
    F4Ipy2BmDPGU5Ebk

    • Use a 10 mm socket to remove the four capped nuts securing the front cover.

    • Remove the front cover.

  6. B4mZdaK3yv6sOwTA

    • Use an 8 mm socket to disconnect the battery wires from the battery terminals.

    • Disconnect the black negative cable first to prevent the risk of shorting the battery.

    • During reassembly, connect the black negative cable first. Make sure you reconnect the wires in the correct polarity.

  7. Rtd2gVSNJQMZfDER
    Rtd2gVSNJQMZfDER
    2VUsPrTZH6UGGAHL

    • Unclip the battery strap from the lower plate.

  8. JUpfTWDkcOFirXJP

    • Remove the battery.

  9. RDZUVKlwTMFoDWqW
    RDZUVKlwTMFoDWqW
    r4IFmRkNHWogk3sr

    • Use a 10 mm socket to remove the four capped nuts securing the lower plate.

    • Set these capped nuts apart. They look similar, but are smaller than the front cover nuts.

    • Remove the lower plate.

  10. bsIFORL3CwVedQRS
    bsIFORL3CwVedQRS
    SkSZvRQJ3uLuFixC

    • Insert a flathead screwdriver into the top of the brown fuse clip in order to release the fuse holder.

    • Detach the fuse holder from the brown clip.

  11. QuHfgHuEQ4VthYnL
    QuHfgHuEQ4VthYnL
    QXdqRVvHKZyuPUNu

    • Use pliers to lift and disconnect the choke cable from the choke stay.

    • During reassembly, be sure to test the choke to ensure that it is properly connected.

  12. Kr1wUlNnspfySpYL

    • Use a long shaft Phillips screwdriver to remove the deeply recessed screw securing the fuel cutoff switch.

    • Be careful not to turn the fuel cutoff switch while you remove the screw.

  13. WxlUVQ2yhw2BNXyB
    WxlUVQ2yhw2BNXyB
    1dkhrTXLElKMKoaR

    • Remove the fuel cutoff switch.

    • During reassembly, be sure to test the switch to ensure that it is properly installed.

  14. RLiROE5UcjRcT6LM

    • Use a 10 mm socket to remove the four bolts securing the control panel.

  15. 2BWAAS6wDiR1qRHQ
    2BWAAS6wDiR1qRHQ
    ToGduqcQLsj2TYUY

    • Carefully tilt the control panel downwards.

    • The control panel will still be connected to many wires and cables. Be careful not to strain any of the connected wires.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Arthur Shi

Mitglied seit: 03/01/18

218620 Reputation

0 Kommentare