Huawei Ascend P6-U06 Earpiece Speaker Replacement

Geschrieben von: Oren Klein
  • Kommentare: 2
Huawei Ascend P6-U06 Earpiece Speaker Replacement

Schwierigkeitsgrad

Moderate

Schritte

16

Zeitaufwand

25 - 35 Minuten

Einleitung

Replace your phone's earpiece speaker to improve call clarity.

  1. Q2x5M4ClsCRDapWN
    Q2x5M4ClsCRDapWN
    fvObMHawhXRQoU6Z

    • Pull and twist the pin near the bottom left-side of the phone to remove it from the headphone jack.

  2. LbIExr6L1V5sBuTe
    LbIExr6L1V5sBuTe
    yKSJLlbv6mgaIFdG

    • Insert the pin into the SIM card opening located on the right-side of the phone.

    • Gently push in until the SIM card clicks, and then pull the pin and SIM card out.

    • Repeat this process for the additional SIM card.

  3. XFIKmrJcrls5M5nB
    XFIKmrJcrls5M5nB
    ZAXA6IZKjRNBBeyH

    • Firmly push down on the black plastic covering at the bottom of the phone, and pull down.

    • You may need a sharp thin object to get underneath the plastic.

  4. tI4cnP5ZbJjNJBFf
    tI4cnP5ZbJjNJBFf
    pxK1sXccy1UPjAUm

    • Rotate the phone 180 degrees so that the bottom of the phone is now facing up.

    • Firmly push up on the back panel with your thumbs.

    • Lift up the back panel from the top right corner and gently pull it away from the phone.

  5. bYUfEODU3bVYhYah
    bYUfEODU3bVYhYah
    a5h6SRSv6XVGxjSi
    VQCigwELMJHDJ2r5

    • Remove the following screws securing the logic board to the main frame:

    • Five 2mm Phillips #000 screws

    • Two 2.5mm Phillips #000 screws

    To replace the battery only the two orange 2.5mm screws need to be removed in this step.

    Jarl Friis -

  6. arI1QSHC2ADenSSD
    arI1QSHC2ADenSSD
    YnpFRUjtC1VlhMrL

    • Push down the yellow plastic lining at the top of the battery and remove the two 2.5mm Phillips #000 screws.

  7. HSjBiT6qOPZm5JQW
    HSjBiT6qOPZm5JQW
    KuutUTUluVP33SAt
    oDeluOHGqovn3hkV

    • Use the flat end of a spudger to gently snap open the first clip located on the the right arm of the retaining plate.

    • Use the flat end of a spudger to gently snap the second clip located on the left arm of the retaining plate.

    • Use the flat end of a spudger to gently lift the upper retaining plate from the phone.

  8. LKcVhMl1KtSxILaM
    LKcVhMl1KtSxILaM
    CIwcuSRNRZcYZiDy
    cjxpveB3CFfQ3GVu

    • Use the pointy end of a spudger to pry the antenna connector off of its socket.

    • Upon reassembly, you will hear a "click" that indicates the pin has been properly reconnected.

  9. nQoBLoDjLyEfRGOs
    nQoBLoDjLyEfRGOs
    nHcbdZgIVZBfRNGW
    VSaRJjqwrDb6yLkC

    • Use the pointy end of a spudger to gently pry the following connectors out of their sockets:

    • silver LCD cable connector

    • silver Headphone jack cable connector

  10. 5QQhP6FCFWttJX3l
    5QQhP6FCFWttJX3l
    YGiRUKiBJUrShYlm
    dBtsLVjMLVfHTRfD

    • Use the pointy end of a spudger to gently pry the following connectors out of their sockets.

    • Sliver Micro-USB cable connector

    • Copper battery cable connector

  11. nryNKwEdSyCm3vkt
    nryNKwEdSyCm3vkt
    ManLFBStDG1ebNEs

    • Be careful not to bend, puncture, or crush the battery, even if it is being replaced. The battery can potentially release toxic and flammable chemicals.

    • Use a plastic opening tool to gently lift up the battery from the bottom end.

    • You may need to loosen the adhesive under the battery with slow sawing motions.

  12. JjMDQkmNIgTLPVWV
    JjMDQkmNIgTLPVWV
    tjOKJhEYpHxCqbod

    • Remove the two 2mm Phillips #000 screws securing the copper flex cable to the silver metal tab.

    • The screw on the left has white paint on the top. Chipping the paint will void any warranty you have for your phone.

    In my new Back Battery cover case there is no possibility to screwing the silver metal tab with these 2 screws to securing the copper flex cable . I only can put the silver metal tab with adhesives (double side tape)

    clbr -

  13. RXPAi1pS4lklHmd1
    RXPAi1pS4lklHmd1
    qfVftDReIHuGs4nV
    xFMVfrOspylBaqRX

    • Wedge the flat end of a spudger underneath the bottom left of the metal tab.

    • Run the spudger along the bottom edge of the metal tab and gently pry upward.

    • Adhesive under the metal tab will make lifting the tab slightly tedious. The adhesive will come off as long as you gently run the spudger along the bottom of the tab.

  14. BmxloHVMTpNPlCDI

    • Gently lift the flex cable from the top-right corner.

    • Do not use excessive force when removing the flex cable. Doing so may tear the cable.

  15. 3LEYAx6paoKYvDSN
    3LEYAx6paoKYvDSN
    ebfFsnZrvMCFymGh
    AfKpNfOnWIrjjlXQ

    • Use tweezers to lift the rubber alignment tab out of its frame.

  16. E15EVgaETWrwLfTo
    E15EVgaETWrwLfTo
    3bMnVYr6KSmn64qf

    • Use the pointy end of a spudger to wedge underneath the earpiece speaker, and gently pry upward.

    • Use tweezers to remove the earpiece speaker from the frame.

    • There is adhesive holding down the earpiece speaker to the frame. If the earpiece speaker is not breaking free, gently wiggle it until it comes loose.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Oren Klein

Mitglied seit: 19/10/14

391 Reputation

0 Kommentare