Huawei P10 Rückkamera ersetzen

Geschrieben von: Dominik Schnabelrauch
  • Kommentare: 18
Huawei P10 Rückkamera ersetzen

Schwierigkeitsgrad

Mittel

Schritte

6

Zeitaufwand

35 Minuten

Einleitung

Verwende diese Anleitung, um die Rückkamera in deinem Huawei P10 Smartphone auszutauschen. Bringe beim Zusammenbau an den erforderlichen Stellen neuen Klebstoff an.

  1. 5kZSF1VgiLHUdyyv
    5kZSF1VgiLHUdyyv
    mQihCqm5GGlSDcKL
    jVG1EPmTTIdtTHi5

    • Schalte dein Smartphone aus.

    • Entferne die beiden Pentalobe P2 Schrauben and der Unterkante.

    • Entferne das SIM Kartenfach.

    Das Honor 9 hat an der Unterkante keine Schrauben.

    Wie ist das Honor 9 zu öffnen?

    Michael Tuschek -

    Vielleicht beantwortet diese Anleitung deine Frage ;)

    Tobias Isakeit -

    Hi, my P10 does not have screws, just two tiny holes. Do I push in here to unfasten? Einar, Norway

    Einar Ryvarden -

    Hi Einar Ryvarden,

    in case you bought a used or refurbished phone, someone might have forgotten to put them back in. Since you have holes at the bottom edge next to the charging port this is likely. You can try to start with step 2 and see if you can lift the phone assembly (don’t forget to remove the SIM tray first). As far as I know there is no version of the regular Huawei P10 with no screws. However you there are none in the P10 lite and in the P10 plus, maybe one of the opening procedures for those phones might help you.

    Dominik Schnabelrauch -

  2. dafShavrRqe1bsKB
    dafShavrRqe1bsKB
    K4uhwPOLpW1gekMx
    oLwmeu5Ptyq4gnEs

    • Führe ein Plastic Opening Tool im unteren Teil des Smartphones zwischen Display und Gehäuse ein.

    • Heble vorsichtig das Display mit seinen Komponenten aus dem Gehäuse.

    • Um das Hebelwerkzeug einzusetzen ist recht viel Kraft erforderlich. Sei vorsichtig und verschiebe das Werkzeug nicht zu sehr, du könntest sonst leicht das Gehäuse beschädigen.

    • Nachdem du den unteren Teil des Smartphones aufgehebelt hast, verwende das Plastic Opening Tool, um die Klemmen an beiden Seiten des Gehäuses zu öffnen.

    Hi! I cannot find a way to insert the plastic opening tool. Any suggestions on how I can create a gap to start. Everything seems quit rigid.

    Also, where will I find your reply.

    vbr/lars.skoldebring@gmail.com

    lars.skoldebring -

    Hi Lars, you might want to use a suction handle to lift the display and create a small gap to insert the plastic tool. If you don’t have a suction handle you can “build” a handle with tape that you stick onto the display in a shape similar to this —> __∏__ (also you may want to edit your post and remove your email address ;) )

    Tobias Isakeit -

    Hi,

    I’m stuck at this step for about two hours… There’s nothing I can do to open the case. Tried all kinds of opening tools and a suction handle. There is no gap at all between the display and the body. How can anything be inserted into a gap that practically does not exist? Please help.

    Mark Movshovich -

    Sorry to hear that. You could try and lift the display by using a suction cup and pull to create a small gap for a tool to get in.

    Tobias Isakeit -

  3. OHcFOOMU1RUU6Qbl
    OHcFOOMU1RUU6Qbl
    HVkOQd4iCx212VAM

    • Öffne das Smartphone noch nicht ganz, da das Kabel für die Standby- und Lautstärketasten noch mit der Rückabdeckung verbunden ist.

    • Hebe das Display an und klappe es leicht nach hinten um.

    • Verwende einen Spudger, um den Stecker des Kabels für den An-/Aus-Schalter so wie die Lautstärkeregelung zu lösen.

    The cable is for the standby and volume buttons, not for the fingerprint sensor!

    JaL -

    Thanks JaL, of course it is.

    Tobias Isakeit -

  4. WUKpybyHSNougxDd
    WUKpybyHSNougxDd
    4e2tZywLIVrUspeO
    TZsdIFAkjGWknOZC

    • Entferne die Kreuzschlitzschraube #00.

    • Verwende eine Pinzette, um die Metallklammer zu entfernen.

    • Verwende einen Spudger, um das Akku-Flachbandkabels vom Motherboard zu lösen.

  5. XVbMjRWGB2eSpww5
    XVbMjRWGB2eSpww5
    oDql2GywkLfJwMIW

    • Entferne die Kreuzschlitzschraube #00.

    • Verwende eine Pinzette, um die Metallklammer zu entfernen.

  6. g5o3pmDCPJIIYHs6
    g5o3pmDCPJIIYHs6
    wukVVSTVivSgTacf
    TlNYRocVDFpOmXTc

    • Verwende eine Pinzette um vorsichtig das untere Ende des Klebestreifens zu lösen, welcher den Stecker des Rückkamerakabels festklebt.

    • Verwende die flache Seite eines Spudgers, um den Stecker des Kamerakabels vom Motherboard zu trennen.

    • Entferne vorsichtig die Rückkamera.

Abschluss

Verwende diese Anleitung in umgekehrter Reihenfolge um dein Gerät wieder zusammen zu bauen. Bringe beim Zusammenbau an den erforderlichen Stellen neuen Klebstoff an.

Tinte & Feder

Dominik Schnabelrauch

Mitglied seit: 23/11/16

167812 Reputation

8 Kommentare

HI, I need to understand why many of us owners of the Huawei P10 has problems with the camera that does not focus or each photo is always blurred and it takes a side kick to fix it temporarily, then I would also know if changing the camera solve the problem. Thank you.

Jean Pierre Valli -

where to get the best rear camera replacement?

Salihin Saealal -

I have replaced the camera in my phone however the replacement does not work. I have seen comments from other people who have had a similar issue such as https://forum.xda-developers.com/p10/hel...

Could this be a firmware related issue? Perhaps the camera firmware in the replacement part is now older than that expected by the firmware in the phone itself?

Does anyone know where to find information about this sort of thing? Whenever I search the Googles I am always taken to generic pages about flashing boot loaders and various versions of Android, not the actual firmware.

Alex Baker -

where I can buy this camera as long as it is original?

pedrosantiagotavares -

What is misssing in detail: how to open the back case from the display. It was very hard and I need another webpage to get additional infromation.

Compi-Sams -

Had the same Problem with the P9. Found something in the coments that did the trick for me: Additional to using the suction cup like mentioned in the instructions i had to (carefully?) preheat the aluminum back with a fan - it will expand slightly more than the glass front or the inside and come off like a charm after.

Florian Bohlken -

Thanks! I couldn’t really get the display out of the back case so I got some instructions from a youtube video for that. Other than that, very clear instructions and photos. My phone has a working rear camera again!

Mischa van Dinter -

Thanks for this.

I successfully managed to change the camera

Ludovic SCOTTI -