Huawei P9 Lite Lautsprecher austauschen.

Geschrieben von: Tobias Isakeit

Kommentare: 15

Huawei P9 Lite Lautsprecher austauschen.

Schwierigkeitsgrad

Mittel

Schritte

Zeitaufwand

Keine Schätzung

Einleitung

Verwende diese Anleitung, um den Lautsprecher deines Huawei P9 Lite zu ersetzen.

Werkzeuge

Schritt 1

Benutze ein Plektrum um die Rückabdeckung abzulösen, beginne damit an der unteren Kante.
Arbeite dich entgegen dem Uhrzeigersinn um die Rückabdeckung herum und löse vorsichtig nach und nach die Klickverbindungen.

What could you use instead of an opening pick??

Alfredo - 27/03/18

Like, could a guitar pick wor? Or anything else?

Alfredo - 27/03/18

A guitar pick will also do.

Tobias Isakeit - 27/03/18

what can still be used besides guitar pick

Tarshia Thompson - 26/11/18

I had a hard time to open the back cover by opening pick. Then I used little, really little knife at first, and I continue to opening back cover using opening pick.

Andy B - 22/02/20

Heating up aroud the finger sensor to loosen the square adhesive tape ..

Hishamchohan - 06/11/20

If you do not have any picks, You can also adapt an old credit or utility card by cutting it in to thirds. Then with some fine emery or sand paper, rub a sharp point on the one edge of the card. This will help you get access to the clips that hold the rear cover on. The one i did yesterday had quite a lot of adhesive around the edge & around the finger print sensor. Another tip with an old credit card is to cut it in to narrow strips to insert in to where you have separated the cover from the frame to stop it getting stuck to the adhesive again.

gazza667 - 06/12/20

Schritt 2

Unter der Rückabdeckung befindet sich etwas Klebstoff, mit dem sie am Akku und an der Metallplatte im oberen Bereich befestigt ist.
Sei vorsichtig mit dem Flachbandkabel auf der rechten Seite.
Verwende das Opening Pick, um die Rückabdeckung nach oben zu hebeln und vom Klebstoff zu lösen.

Most of the adhesive is around the fingerprint cell and on the battery itself. You can slowly pull the back cover from its side but make sure not to break it. Push the mediator or a longer piece of plastic under the back cover to slowly destroy the adhesive.

Nicolas Combaret - 22/04/19

Slowly, slowly wins the day. Nicolas is right and comes off a charm. The most nerve wracking part of this longish repair.

John Nordstrom - 20/06/20

Schritt 3

Wenn die Rückabdeckung vom Kleber befreit, kannst du sie vollständig abnehmen.

Hi! Im so sad! At the begginig of the operation i ve broken the white seal/connector that in one side is connected to the board and the other side is "glued" to the battery. Can someone help me? how can i solve this?? There is no image displayed on the screen. but there is vibration, sound, notifications... can someone help me please???

Diogo - 01/07/17

What you broke is handling the NFC, and doesn’t have anything to do with the display. You probably damaged the ribbon right below the battery, since that’s what links the display to the motherboard.

Polaris -

Oups ! L’antenne NFC était solidement collée à l’intérieur de la coque et j’ai donc déchiré sa nappe en ouvrant la coque. Heureusement, je n’utilise pas les fonctions NFC et, à part cela, tout a l’air de fonctionner normalement.

Michel Orban - 26/01/21