LG G Pad 8.3 Rear Facing Camera Replacement

Geschrieben von: Mario Salguero
  • Kommentare: 3
LG G Pad 8.3 Rear Facing Camera Replacement

Schwierigkeitsgrad

Moderate

Schritte

13

Zeitaufwand

20 Minuten

Einleitung

If your rear facing camera is not working, it may be time to replace it. This guide will show you how to replace the rear facing camera.

  1. sOJUcVTNoWWtVGDR
    sOJUcVTNoWWtVGDR
    eM32UNGNWqgmFWva

    • With the tablet face down, pull the SD card slot cover out.

    • Using a Phillips #000 screwdriver, remove the 3mm screw located in the SD card slot.

  2. qDRkREMwYUAkwGQX
    qDRkREMwYUAkwGQX
    NT4FQU2PqhmRBfGS
    RcAxS1nRODfFM5bu

    • Insert a plastic opening tool in the small crevasse between the screen and the back panel.

    • Pry the screen away from the back panel.

    • Repeat this on each edge of the device.

    • We found it helpful to leave multiple plastic opening tools wedged in the crevasse to prevent it from closing.

    • This requires heavy force. The back of the device is attached with an adhesive. If the back panel is too hard to remove, use the iOpener.

  3. ko5XAEW4Ivc3xRJN
    ko5XAEW4Ivc3xRJN
    QkkrZPVEyrauxxOt

    • After using the plastic opening tools, pry the device open with your hands.

    • Remove the back panel from the screen.

  4. spIW5UxFGfHeCAxF
    spIW5UxFGfHeCAxF
    dJySR5RjGiMR3plP

    • Remove the four 3 mm Phillips #000 screws that are attached to the speaker.

    • These screws are very small so make sure to keep track of them. You can use iFixit's Pro Magnetic Project Mat to help.

    On the VK810 Model you have to watch out for the antenna wire that runs along and is attached to the speaker by the means of a metal wire clip.

    What I would recommend is detaching the antenna wire from the top of the device then gently remove it from the clip.

    Then remove the speaker.

    On a side note does anyone know where to buy the little ant wire that runs across the speaker?

    Kyle -

  5. BGWfCY3cmO5hbACX

    • Use your fingers to remove the speaker.

  6. 4q1PgFiOGfn3ZY1n
    4q1PgFiOGfn3ZY1n
    yfWgZtPNGyOlCYCZ

    • Remove the 3mm Phillips #000 screws from the corners of the battery.

  7. GCBXHnYVCiuIgafT
    GCBXHnYVCiuIgafT
    EEsH6HxSfsPxHBxh
    JLPWpsBTF6ywAVpE

    • Using a spudger or a plastic opening tool, disconnect the ribbon cable from the right side of the device.

    • The cable is attached with an adhesive.

    • These images use a metal spudger, which has the potential to damage the device. Use a plastic opening tool or standard spudger instead.

  8. OxvPkLWQGLQZaEKh
    OxvPkLWQGLQZaEKh
    j23bFABhJ2hI2ZVB

    • Using the Phillips #000 screwdriver, remove the two 3mm screws located at the bottom of the ribbon cable.

    • Remove the ribbon cable from the device.

  9. 4xKfwwucKyShcS2Q
    4xKfwwucKyShcS2Q
    m1ybvI4Vl2GdHosg

    • Unhook the battery from the top of the device.

    Watch out: I had to remove the mainboard first, before being able to lift the battery with its attached hook on top.

    Sven Meier -

    The screen on my device separated from the main board which is still in the back of the device. I can’t get to the under side to remove the speakers and battery.

    Chris C -

  10. L3uPeZHXmdp5vIXv

    • Unhook the small yellow ribbon on top of the motherboard.

  11. 6GWjTqPo5ce1rIO4

    • Remove all the 3mm silver screws and the 2mm black screws on the motherboard and carefully lift it out of the device.

  12. I6lIAh2uZJtluOfl
    I6lIAh2uZJtluOfl
    tATVaKN4c1IDwiMQ

    • Use a plastic opening tool to lift the motherboard out of the device.

    • These images use a metal spudger, which has the potential to damage the device. Use a plastic opening tool or standard spudger instead.

  13. vAXWVVbTNYbHBHCW
    vAXWVVbTNYbHBHCW
    YrD6DflSsaaMQl6G

    • Use a plastic opening tool to remove the camera, which is attached with adhesive to the front of the tablet.

    • These images use a metal spudger, which has the potential to damage the device. Use a plastic opening tool or standard spudger instead.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Mario Salguero

Mitglied seit: 14/09/15

781 Reputation

0 Kommentare