LG Vortex Rear Facing Camera Replacement

Geschrieben von: Jen
  • Kommentare: 1
LG Vortex Rear Facing Camera Replacement

Schwierigkeitsgrad

Moderate

Schritte

11

Zeitaufwand

30 - 45 Minuten

Einleitung

Follow the initial LG Vortex Disassembly guide before you begin camera replacement. This guide takes you step-by-step through the replacement of the LG Vortex camera.

  1. Mhye11DPvMdgvtbo

    • Power the phone off

    • The power button is located on top of the phone

  2. PcfwyBykuFZUA66k
    PcfwyBykuFZUA66k
    gbCMNDcE1dv445FZ
    RRL2WHkOKWDUxPko

    • Find the two thumbnail ridges on the side and top of the phone.

    • One is next to the micro SD slot and the other at the top of the phone

    • Once the ridges are located, use the blue plastic opening tool to pry the back cover away from the rest of the phone.

    • Remove the back cover and set it to the side.

  3. ugNQHTaIEtZAHJPQ

    • Remove the battery using the blue plastic opening tool.

    • There is a small thumbnail ridge at the top left corner of the battery for ease of removal.

    • Put the battery aside.

  4. smmXheHhVk1RtRhf
    smmXheHhVk1RtRhf
    nre3VslUKB4dA62G

    • NOTE: All screws are the same size

    • Use the precision screwdriver head #00 to remove the 6 screws along the edges of the phone.

    • There are 2 screws at the top in each corner, 2 in the middle on the sides, and 2 in the bottom corners.

    • Place the screws in the small container to ensure they aren't lost.

  5. ALkWa4ERHMVS1Xle
    ALkWa4ERHMVS1Xle
    cpgZpOJvPH2bJAiS
    BMqZHVC1UCAu131u

    • Use the blue plastic opening tool to remove the back frame from the rest of the phone.

    • Pry at the micro SD slot. Push the cover for the SD slot away from the front of the phone and pry the back frame away from the rest of the phone.

    • Pry your way around the entire phone to separate the face from the frame.

  6. XIA1yvklasdQFdpk
    XIA1yvklasdQFdpk
    UNDZaSI1TCFUgbNK
    k1RdeohdpYqs5BBL

    • NOTE: This is the most difficult step.

    • Locate system board (silicone board with all of the circuitry on it). Notice that there is a black piece at the top of the system board (with the camera in it).

    • Use the pry bar to push the 2 black tabs away from the system board (located on the sides of the board). These tabs may snap back onto the board, so attempt to hold them off of the board.

    • Use the pry bar to pry the black piece at the top of the phone (looks to be attached to the system board, but is not).

  7. uvA3cGr3BWJX1AQ2

    • NOTE: Do not damage the thin wires attaching the motherboard to the speakers

    • Using the blue plastic prying tool remove the black piece next to the camera.

  8. Hv5AWbqCmAMyQrsQ

    • NOTE: Remove with caution.

    • Disconnect the cord attaching the camera to the system board.

    • (It looks like a thin piece of plastic)

  9. duYAv5fNucCysgJf
    duYAv5fNucCysgJf
    cY5wdtelISVlKskT
    J3iNOLCg1sIBkGns

    • The camera is held on by 1 sticker on the top of the camera.

    • Remove this sticker using your fingernail.

    • Pull the camera off the system board using your fingers. Perform this step with caution.

  10. bY3SXxFGA2DHMvu2

    • Place new camera in the same location, and place the sticker back on its side.

  11. qYkXXBqkIy4bNjdG

    • Reverse the steps to reassemble the phone.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Jen

Mitglied seit: 13/02/14

4 Reputation

Ein Kommentar

First, clean the cookware with water and a mild kitchen soap to remove anything that might be on the surface. Rinse with hot water. I do uk.bestessays.com and Then coat the entire bottom of the pan in vegetable oil in this case, canola oil and turn it over onto a paper towel for 10 minutes.

William Peter -