Lenovo Miix 2 Motherboard Replacement

Geschrieben von: Diana Chiu
  • Kommentare: 4
Lenovo Miix 2 Motherboard Replacement

Schwierigkeitsgrad

Easy

Schritte

11

Zeitaufwand

10 Minuten

Einleitung

After removing the back case and battery, the motherboard is easy to remove from the Miix 2.

  1. 12Hk4GxWiybsEHyD
    12Hk4GxWiybsEHyD
    Gw5FW6nhL6QtTtJA

    • Remove the back cover of the tablet by inserting a nylon or metal spudger in the small hole between the screen and rear cover near the volume button. Slide the tool along the edge of the tablet to release the internal clasps.

    • You should have to apply a good amount of force, but pry carefully in order to avoid damaging the clasps or the internals.

  2. Y3jRH4vZ64wPeU5B
    Y3jRH4vZ64wPeU5B
    XRSTVdbMSLOYiTwF

    • Unscrew the six 3mm screws surrounding the battery dock using a Phillips #0 screwdriver.

  3. 6QsV5HaJKYADWB2E
    6QsV5HaJKYADWB2E
    etXteVIrhgwBtcLs

    • Using a plastic spudger, slowly push each side of the battery connector (back and forward a couple of times) out of its socket on the motherboard.

  4. UxjbpUHqRQLhKX12
    UxjbpUHqRQLhKX12
    LwZlE6OkmF6jZdDM

    • Remove the battery by prying up with your fingers or a plastic opening tool.

  5. 1VpjqOqMxyrW1NaO
    1VpjqOqMxyrW1NaO
    YpLDBgajQAyQCXYo

    • Remove the red and black connector cable linking the speakers to the motherboard with tweezers by pulling the connector to the left with a light degree of force.

    • To properly remove the speakers from the casing, push gently left until it shifts, then pull directly up.

  6. PJZZWENKfdvTfPZh
    PJZZWENKfdvTfPZh
    m21JXy1IjCnHH2AT

    • Locate the LCD cable connector and gently pry it directly up with a spudger.

  7. cLUfMuDV3BVLqCFD
    cLUfMuDV3BVLqCFD
    FlKWU3yO2ikBdNvf
    MYXIjDulAUnqwmWh

    • Remove the 5 ribbon cables. use the tip of the spudger to flip up the retaining flap, making sure to lift on the hinge and not the connector itself, then remove the cable from the connector.

    • The flaps and connectors vary in color.

    • Once the hinge has been lifted, the ribbon cable should take no force to remove.

    I would recommend putting some double sided padded tape above the connector labeled MB once you get the connector back on - that's the infamous touchscreen cable that comes loose once in awhile. This will effectively wedge the cable in place and keep it from falling out.

    Kevin Kwan -

  8. HiLnpqp1Egylvupg
    HiLnpqp1Egylvupg
    amc2EpoYR2tbpjlc

    • Remove the 3 antenna cables using the tweezers by slowly pulling up.

    • We found that pulling up and twisting a bit works best.

  9. k3GvACKIVPZqcJCG
    k3GvACKIVPZqcJCG
    NfUVAVsWPgxgCCfu

    • Remove the 4 1.6mm screws with a J0 head.

  10. VWvCUQLFWBFi1Bq6
    VWvCUQLFWBFi1Bq6
    2GnLivwyjCPmtUtb

    • Remove the red and black cable using the tweezers by gently pulling the connector to the right.

  11. kpXxXHdRlPPLwpWt

    • Lift the motherboard out of the tablet's case.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Diana Chiu

Mitglied seit: 15/07/14

654 Reputation

3 Kommentare

Do i need to update the BIOS once i have done this?

Do i also need to update the serial number of the machine?

dennis bortolin -

No, you should not have to upflash the BIOS and re-tattoo the machine - Assuming your replacement board has the proper OS entitlements already tattooed onto the UEFI , it should be picked up by the OS (Windows 10, I hope) and automatically re-activated. In fact, I imaged a Miix 2 8 out using a bootable USB drive + Clonezilla, and was able to image it into a new board and have everything re-activate just fine.

Kevin Kwan -

Is the micro usb port detachable? It seems soldered on from the pictures. I'm having trouble with the port. It charges the device but when I add an OTG cable the device dosnt power the USB and it dosnt detect it. Tried with a keyboard too, no response.

Dave -