Lenovo Y410P Motherboard Replacement

Geschrieben von: Eric Chen
  • Kommentare: 2
Lenovo Y410P Motherboard Replacement

Schwierigkeitsgrad

Moderate

Schritte

7

Zeitaufwand

1 - 2 Stunden

Einleitung

Motherboard replacement can be necessary if the motherboard is damaged or malfunctioning. Be careful during replacement, as many of the components are fragile. Be sure to use proper tools to avoid damaging any screws or other components.

  1. OhBbrmiZWv1GUZDy
    OhBbrmiZWv1GUZDy
    3YoNQmvBeFnPICQn

    • Remove eight M2.5 x 8mm Phillips head screws, using a Phillips #0 screwdriver, in the specified locations.

    • Lift the bottom cover off and set it aside.

  2. KmKOTgqucBG2CoHE
    KmKOTgqucBG2CoHE
    VIjfhLIlSkaX2RBo

    • Remove the two M2.5x4mm screws using a Phillips #0 screwdriver.

    • Slide the hard drive out of the casing.

    • Be careful when handling the hard drive; rough impacts may cause data loss.

  3. gC2mBJmntQ2peI1V
    gC2mBJmntQ2peI1V
    QGy1Gois2FxWhGdb
    SQsDT2KBoETZxw1I

    • With the laptop's bottom facing up, pull the optical drive release lever back and pull the optical drive out.

    • Unscrew the three M2x3mm Phillips head screws shown.

    • At the front edge of the laptop, empty the SD card holder by pressing on the card. This will allow for further disassembly in later steps.

  4. nUOQHQroMAsVBEV5
    nUOQHQroMAsVBEV5
    X1fFZvtosTvYRHM4

    • Remove the two M2.5 x 6mm screws using a Phillips #00 screwdriver.

    • Disconnect the two WiFi antenna cables.

    • Disconnect the sound connector.

  5. foyMH5iTTXF1SYpY

    • Open the laptop hinge. Tip the laptop onto its side, and use the back end of the screwdriver to push the keyboard out from the optical drive area.

    • Turn the laptop right side up and pry the keyboard up slowly, until it is clear of the case.

    • Be careful of the ribbon cable when removing the keyboard. The ribbon is still attached.

    • Detach the ribbon cables by opening the specified latches.

  6. Np2nfryN4NnDporB
    Np2nfryN4NnDporB
    ROEHlEvRJEolGMTS
    2CNg3CtArelyxOfP

    • Detach the ribbon cables by opening the specified latches.

    • Turn the laptop upside down and remove the M2.5x8mm screw with Phillips #0 screwdriver.

    • Turn the laptop on its side and pry the bottom from the top.

    • Only partially remove the palm rest; there is still a ribbon cable attached underneath it.

    • Remove the ribbon cable by opening its respective latch.

  7. R2sPbSPRAXe1iGv2
    R2sPbSPRAXe1iGv2
    hXRjL5O3Id1o55XP
    vaH1XnokPsreMAn2

    • Remove the specified cable on top of the motherboard.

    • Flip the laptop over, and remove the specified cables.

    • Remove the two M2.5x4mm screws with a Phillips #0 screwdriver

    • Remove the motherboard with hands.

    My y410p can't start, overheat in some are in motherboard

    Fauzy Sadland -

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Eric Chen

Mitglied seit: 22/01/15

868 Reputation

Ein Kommentar

there are 2 screws near the battery lock that you need to remove when removing the palm rest

JM -