Logitech Harmony Smart Keyboard Back Panel

Geschrieben von: Hayley Nichols
  • Kommentare: 0
Logitech Harmony Smart Keyboard Back Panel

Schwierigkeitsgrad

Easy

Schritte

9

Zeitaufwand

10 - 15 Minuten

Einleitung

This is a prerequisite guide that will instruct you on how to properly open your keyboard. This will be helpful for replacing internal components without damaging your device.

  1. yeFWtiLBjSocyENG
    yeFWtiLBjSocyENG
    3BwD5hli2x1iLHhH

    • Turn keyboard over to the backside.

  2. bkilisV2dQGEFneF
    bkilisV2dQGEFneF
    L4Q6NyWEELcmN3MN
    ZsF2eLBUFaQNrbng

    • Press and slide up on the upper battery latch, using both thumbs.

  3. JgKfbQkckWndfV33

    • Remove the two AA batteries and set them aside.

  4. lqVPdDa2PXLNpiSU
    lqVPdDa2PXLNpiSU
    MwoTmVWnwIVdSHsw

    • Unscrew all five 4.0 mm screws, using Phillips #1 screwdriver.

  5. MXrNtLXF3pKjVfQD
    MXrNtLXF3pKjVfQD
    iFygMbZQXpbCGdIX

    • Peel off the center sticker to reveal two hidden 4.0 mm screws.

    • Unscrew these two screws with a Phillips #1 screwdriver.

  6. BFMJEZKGEgMUHwNF
    BFMJEZKGEgMUHwNF
    cllVdhlf45PBQTUt
    dT3NWxDTPZZxKbtX

    • Lift both top left and top right rubber stickers halfway, using the sharp end of the plastic spudger.

    • Unscrew a total of two 4.0 mm screws, under the rubber stickers, using a Phillips #1 screwdriver.

  7. qhQFV4c2R6AZctUI
    qhQFV4c2R6AZctUI
    tvNV5yDa4AMypJFc

    • Unscrew the top center 4.0 mm screw, in the battery compartment, using the Phillips #1 screwdriver.

    • Now, you should have a total of ten 4.0 mm screws set aside.

  8. QvfEWbEEhCQ3RRP5
    QvfEWbEEhCQ3RRP5
    1AePc6T3aahPEOTZ
    2AJSDA35Ir3ZbWLD

    • Wedge the flat end of the spudger between the back panel and front panel.

    • Slide the flat end of the spudger from right to left to pry the two panels apart.

  9. cDZ4OUrr5gyGT1PT
    cDZ4OUrr5gyGT1PT
    XIY3ovvr4Ts4MCef
    DY4UKtsBnNFgW1aW

    • Separate the back panel from the front panel completely, using both hands.

    • A white ribbon flex cable will remain connected to both panels.

    • Pull the panels apart slowly and gently, or the white ribbon flex cable may be unsafely removed.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Hayley Nichols

Mitglied seit: 05/09/17

507 Reputation

0 Kommentare