MSI GT70 MS-1763 Keyboard Replacement

Geschrieben von: Bhrett Farrar
  • Kommentare: 1
MSI GT70 MS-1763 Keyboard Replacement

Schwierigkeitsgrad

Moderate

Schritte

10

Zeitaufwand

30 Minuten

Einleitung

The keyboard is an input peripheral/interface on your device that will occasionally have keys stick or not function properly. Follow the steps below if you need to replace the keyboard on your MSI GT70 MS-1763. Keep in mind that the keyboard must be replaced as a single unit. The MPN is

S1N-3EUS204, V139922AK1

  1. KxPVkuOJTaCqXm3A
    KxPVkuOJTaCqXm3A
    YkuAAPEvZGUg4ZTG

    • Power off the laptop and turn it over.

  2. fw2M6dc6DSoqSxZD
    fw2M6dc6DSoqSxZD
    SSgLWxYM2qBgNO4A

    • Release the safety latches that hold the battery in place. The left latch will stay moved up, while the right side is spring activated and will have to be held.

  3. dOyOSKxlfa4ScCPp
    dOyOSKxlfa4ScCPp
    JuGv6RQlZHulABRB

    • While holding up the left latch, use a Jimmy and slide the old battery out of its compartment.

  4. YlMOxCfDgLI4GOny
    YlMOxCfDgLI4GOny
    gVZ3XUkiaNqCon1X

    • Remove all twelve 4 mm Phillips #0 screws from the back of the laptop.

    • Remove the back cover.

  5. qW5vDoCkjDVxvI3T

    • Remove the rubber spacer holding the hard drive secure.

  6. DvBg6MQ646AWGORl
    DvBg6MQ646AWGORl
    WfRQ2uJjElbWhYJX

    • Slide the hard drive to the left, removing it from its bay.

  7. arGjSoKcu1EEMMev
    arGjSoKcu1EEMMev
    XWQOtsRkRc3BMaLM
    GsAlcRV4nNE1Sfs6

    • Using a Jimmy, remove the outer cover around the keyboard.

    • Remove the ribbon cable from the ZIF connector on the underside of the top cover.

  8. WExPYOPEfKZEWLbe
    WExPYOPEfKZEWLbe
    PAouIbPP2XDDwBBn

    • Using a Phillips #0 screwdriver, remove the five 3 mm screws at the top of the keyboard.

  9. AlMdAPZ6KBsFC62P

    • Flip the keyboard back and disconnect the keyboard cable.

  10. SAWggUxI5g2cGITS
    SAWggUxI5g2cGITS
    ELheGAaGFucBthy5
    lUlauKCcXZKahTVL

    • Flip the laptop over and disconnect the data cable from the ZIF connector on the bottom right.

    • You can now turn the laptop back over and remove the keyboard.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Bhrett Farrar

Mitglied seit: 22/08/19

109 Reputation

Ein Kommentar

Mine is the Cyberbuypower rebadge of this model. And you only need to remove the two keyboards screws on the bottom. And then the top button board (called outer cover here)

Even here I don’t see why you have to remove all those screws.

garegin -