Einleitung

Use this guide to service the bolt of the Makita Jack Hammer HM1203C 2010.

Wherever there’s grease, make sure to clean it off and replace it with new grease. The recommended grease is Makita 181490-7.

  1. rVabLGJNSEsYg5Cy
    • Unscrew the knob securing the side handle.

  2. OyTA2gNSdjR1kmPD
    OyTA2gNSdjR1kmPD
    4A4UWnQe6jEyth2Z
    • Remove the bolt securing the side handle.

    • Remove the side handle.

  3. cdQPCAWmHlpZuqwk
    cdQPCAWmHlpZuqwk
    WZytVuLQoM1IdOQu
    2HIlqhpLeAyFxAo3
    • Use a small pry bar or flathead screwdriver to pry the rubber front cap off of the hammer.

    • This can be replaced as part of a service kit.

  4. MgV3kvWneQQTL1Ua
    MgV3kvWneQQTL1Ua
    vMXLTYjODTqRU6hN
    • Use a pair of snap ring pliers to expand the snap ring on the front of the hammer.

    • Remove the snap ring.

  5. YNdUfUDuBlW3iwTE
    • Remove the washer on the front of the hammer.

  6. Xv6FAVtBrvCNwHY2
    • Lift the front cover off of the front of the hammer.

  7. UAYHeEwcanQlXHDa
    • Lift the rubber ring off of the front of the hammer.

  8. UJtMSM6sCVyYTl6s
    • Remove the inner front cover.

  9. uET4fb1PCjtlCE6N
    uET4fb1PCjtlCE6N
    Mv34bjlW5lTgb65W
    JDmRNiEcB4NoTTF2
    • Compress the spring and hold it down while you pull the two retainers out of their slots and remove them.

  10. MNKsmQJGMqsP5XDa
    MNKsmQJGMqsP5XDa
    Q2QuwMBEDUv3QVMM
    • Remove the spring guide.

    • Remove the spring.

  11. rLKJWivqtGhfl2pW
    rLKJWivqtGhfl2pW
    EoqqGBoAoqKv1miP
    • Remove the front barrel cover.

  12. SrrnNhjdOsoOL4RD
    • Remove the 4 mm hex bolt securing the barrel cover.

  13. Y4Akq2MLOTXs3DEg
    Y4Akq2MLOTXs3DEg
    QDbKrTrCnl1OEXDr
    • Lift the barrel cover straight up and remove it.

  14. OpXCXwLmdr3tJfSF
    OpXCXwLmdr3tJfSF
    1QjODJKmdeVBid2s
    • Use a pair of snap ring pliers to expand the snap ring securing the bolt holder.

    • Remove the snap ring.

  15. dCjOle4udFT1ZZDK
    dCjOle4udFT1ZZDK
    CKkiZonsa4hcAnsB
    • Lift the washer off of the bolt holder and remove it.

  16. kDcWno3nrDMoNNEC
    • Remove four 6 mm hex bolts securing the barrel.

  17. OJGjAmiR1XQQHjnD
    OJGjAmiR1XQQHjnD
    Iho5nYAKThTmJQZ3
    • Lift the barrel straight up and remove it.

  18. RRDHVfZBG4rtpfvJ
    RRDHVfZBG4rtpfvJ
    eJhe3RQs5xg2nJBe
    EV6LuLpwo223ECYm
    • Use an angled pick to pull the washer and rubber ring 39 out of the barrel.

  19. NPqnApVFWsEUyh1J
    • Remove the rubber ring 39.

    • This can be replaced as part of a service kit.

  20. kiYodUQxFOwcKGkS
    • Lift the upper-most rubber ring straight up and remove it from the bolt holder.

  21. 2t2mjah3Ms1xiDDF
    • Lift the upper-most washer straight up and off of the bolt holder.

  22. qU6H2L2FRG3FZ2AQ
    qU6H2L2FRG3FZ2AQ
    s5UrEfyTMBTvBwJm
    • Grasp the bolt holder, rubber ring 24, and the two metal sleeves below it, and lift it off of the cylinder.

  23. sL5kUNSgYudKPnwQ
    sL5kUNSgYudKPnwQ
    sbuotdNAKOA6imTS
    • Separate the rubber ring 24 and the two metal sleeves from the bolt holder.

  24. HVn5GlLDUTQlNpJZ
    HVn5GlLDUTQlNpJZ
    v6qICGYR2G5Wdw1T
    • Separate the rubber ring 24 from the two metal sleeves.

    • Remove the rubber ring 24.

    • This can be replaced as part of a service kit.

  25. LwPRlJqbB1imX5hX
    LwPRlJqbB1imX5hX
    bbiHg1PfpiCLDwZA
    • Use an angled pick to lift the O-ring 35.5 out of its groove on the bolt holder.

    • Remove the O-ring 35.5.

    • This can be replaced as part of a service kit.

  26. xGDsrr2tyxTUKUyB
    xGDsrr2tyxTUKUyB
    UZcT2kRI2mDgGAVK
    • Use a long punch, long flathead screwdriver, or a thin, long bar to push the bolt out of the bolt holder.

    • Remove the bolt.

    • During reassembly, make sure all the seals on the bolt stay seated properly while you slide the bolt back into the holder.

  27. 4fmnQAmTRmJOeShQ
    4fmnQAmTRmJOeShQ
    CNPqYgLrtVPqYC2U
    • Use an angled pick to pry the X-ring 21 out of its groove in the bolt.

    • Remove the X-ring 21.

    • This can be replaced as part of a service kit.

  28. LJYu5OYreeQGErPq
    LJYu5OYreeQGErPq
    OHDlqDQToDOJ2tXe
    • Use an angled pick to pry the fluoride ring 28 out of its groove in the bolt.

    • Remove the fluoride ring 28.

    • This can be replaced as part of a service kit.

  29. rVwLkXjtZaWl1gSf
    rVwLkXjtZaWl1gSf
    6hGJcpiEXPofTcqv
    • Use an angled pick to pry the O-ring 23 out of its groove in the bolt.

    • Remove the O-ring 23.

    • This can be replaced as part of a service kit.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Adam O'Camb

Mitglied seit: 11/04/15

178852 Reputation

0 Kommentare