Matsunichi M97 9 inch Motherboard Replacement

Geschrieben von: Christopher
  • Kommentare: 0
Matsunichi M97 9 inch Motherboard Replacement

Schwierigkeitsgrad

Moderate

Schritte

13

Zeitaufwand

15 - 20 Minuten

Einleitung

The Matsunichi M97 was a cheap alternative to the more common tablets. But it has its faults. Due to charging issues and/or functionality problems, the motherboard may need to be replaced. This guide will aid in diagnosing any problems with the device.

  1. EFl3eeaPI2DUSBDx

    • Open the micro SD cover located on the back of the device.

  2. DWxSMI3WK4pYMs1H

    • Using the Phillips #00 screwdriver, remove the two 4mm screws next to the micro SD port.

  3. bMWXEXKLeKAbJ6ea
    bMWXEXKLeKAbJ6ea
    irObTgNh6NNuqA2V
    bjlqon6aTAkvHvJK

    • Use the iFixit opening tool to pry off the back cover of the device.

    • The volume buttons and the lock switch will come loose when the back comes off.

  4. iH2HHU26TMEe5FU2
    iH2HHU26TMEe5FU2
    kXpSMVuNHRJoYT4v

    • Use a pair of tweezers to disconnect the battery from the motherboard.

  5. H6KSqAn3PneL5dBM
    H6KSqAn3PneL5dBM
    ewLT6r3pZYbuupOq

    • Carefully unstick the battery from the frame using the spudger.

    • Do not bend or puncture the battery during removal.

  6. LiWmMXi6WuhDIgZu
    LiWmMXi6WuhDIgZu
    gsAKMAPHpEhaxGVW

    • Remove the six 2mm screws that hold the motherboard onto the case using the Phillips #00 screwdriver.

    • Use the same screwdriver to remove the single 4mm screw.

  7. OZEXXYJU2hUxyEbv
    OZEXXYJU2hUxyEbv
    F6qO1f3PP4thVRXa

    • Gently pull the display ribbon cable to unplug it from the motherboard.

  8. DNZRUuLOmgiCVBl4

    • Use a spudger or an iFixit opening tool to lift the locking mechanism holding the camera ribbon cable.

  9. NIs2w1XIQMVnjGWB
    NIs2w1XIQMVnjGWB
    qfyJDwftwJKFHAAq

    • Lift up on the wifi antenna cable to unsnap it from the motherboard.

    • Then unhook the cable from the holding bracket.

  10. YnlQemJDGpxLYMtg
    YnlQemJDGpxLYMtg
    mYAuuSdIW6mCfSWX

    • Use the spudger or iFixit opening tool to lift up on the locking mechanism for the digitizer ribbon cable.

    • Pull the cable from its connection.

  11. nUOGwqFtdFvk3cOq
    nUOGwqFtdFvk3cOq
    RRjYbDEuuEDtFXlD

    • Use the Phillips #00 screwdriver to remove the four 4mm screws that hold the speakers in place.

  12. QUoGv5XJa6DvWOhh

    • Pull the vibration motor out of its housing.

  13. i5XURt5p6D2ZUImJ
    i5XURt5p6D2ZUImJ
    LRP2LFVLLkNng3AH

    • Lift the motherboard off the frame.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Christopher

Mitglied seit: 16/01/20

246 Reputation

0 Kommentare